How in the world do you get it out of the plastic holder after you unbolt it from the floor? The Liberty's manual shows the jack already out of the holder.
Thanks,
T.J.
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Question about the included KJ jack http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=14702 |
Page 1 of 1 |
| Author: | Video Guy [ Mon Nov 20, 2006 1:38 pm ] |
| Post subject: | Question about the included KJ jack |
How in the world do you get it out of the plastic holder after you unbolt it from the floor? The Liberty's manual shows the jack already out of the holder.
Thanks, T.J. |
|
| Author: | bugnout [ Mon Nov 20, 2006 2:04 pm ] |
| Post subject: | |
I believe you just need to turn it down. Its shipped extended to compress against the holder. |
|
| Author: | JMLoughrey [ Mon Nov 20, 2006 2:43 pm ] |
| Post subject: | |
yup, just turn it so its completly compressed. It should then wiggle out. It gets stopped on one side due to the way the plastic is to keep it held in place. |
|
| Author: | KJ-BOL [ Mon Nov 20, 2006 3:28 pm ] |
| Post subject: | |
Now that you have a lift, make sure you carry some 2x4s as base for the stock jack - otherwise you will not be able to get the tire off the ground to change in case of a flat.... |
|
| Author: | 2006KJSPORT4x4 [ Mon Nov 20, 2006 5:15 pm ] |
| Post subject: | |
Also if you are in wreck like FLJeep was and myself, most likely the jack will fly out from it's position underneath the passenger bench....thus i installed a block of wood from bench support to bench support to prevent stuff from flying out from underneath the bench seat... |
|
| Author: | chetos [ Mon Nov 20, 2006 5:20 pm ] |
| Post subject: | |
OOPPSSS! I couldn't get mine out of the plastic and man handled it a bit and the plastic broke just a little bit!  
|
|
| Author: | Jeepjeepster [ Mon Nov 20, 2006 5:22 pm ] |
| Post subject: | |
chetos wrote: OOPPSSS! I couldn't get mine out of the plastic and man handled it a bit and the plastic broke just a little bit!
You shouldn't man handle things.
|
|
| Author: | Gentleman [ Tue Nov 21, 2006 11:17 am ] |
| Post subject: | |
When did Jeep change from a bottle jack to a scisssors jack, every liberty jack I see for sale on ebay is the bottle type, the parts break list for 05 pictures a bottle jack, but the jack you get is a scissors. Bob |
|
| Author: | Tokyojoe [ Tue Nov 21, 2006 12:18 pm ] |
| Post subject: | |
I have an `04 Reny and it is a scissor jack. |
|
| Author: | hyedipin [ Tue Nov 21, 2006 12:58 pm ] |
| Post subject: | |
RockyMtEditionKJ wrote: Also if you are in wreck like FLJeep was and myself, most likely the jack will fly out from it's position underneath the passenger bench....thus i installed a block of wood from bench support to bench support to prevent stuff from flying out from underneath the bench seat...
doesn't yours come with a screw to secure it to the floor? |
|
| Author: | bugnout [ Tue Nov 21, 2006 1:01 pm ] |
| Post subject: | |
Gentleman wrote: When did Jeep change from a bottle jack to a scisssors jack, every liberty jack I see for sale on ebay is the bottle type, the parts break list for 05 pictures a bottle jack, but the jack you get is a scissors.
Quote: Everyone I have seen in the U.S. comes with a scissors jack. Replaced mine with a bottle jack right after I installed the lift. |
|
| Author: | 2006KJSPORT4x4 [ Tue Nov 21, 2006 1:03 pm ] |
| Post subject: | |
hyedipin wrote: RockyMtEditionKJ wrote: Also if you are in wreck like FLJeep was and myself, most likely the jack will fly out from it's position underneath the passenger bench....thus i installed a block of wood from bench support to bench support to prevent stuff from flying out from underneath the bench seat... doesn't yours come with a screw to secure it to the floor? It does but it was sheared off and the jack flew underneath my front passenger seat...i'd feel sorry for a passenger of mine in the back if they were sitting there when that thing launched out at their achilles.... 
|
|
| Author: | hyedipin [ Tue Nov 21, 2006 1:09 pm ] |
| Post subject: | |
Ouch. |
|
| Author: | Jeepjeepster [ Tue Nov 21, 2006 9:38 pm ] |
| Post subject: | |
Tokyojoe wrote: I have an `04 Reny and it is a scissor jack.
Me too. I already crushed it.. 
|
|
| Author: | Goglio704 [ Tue Nov 21, 2006 9:41 pm ] |
| Post subject: | |
The 2 x 4 idea is valid with an unlifted Liberty too. When mine had a flat the jack wouldn't raise it high enough. Stock height, stock tires, on level pavement. Maybe it was a Compass jack? 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|