LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Front fender trimming
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=22088		 Page 1 of 1
Author:  jdumont [ Fri Jun 29, 2007 3:09 pm ]
Post subject:  Front fender trimming
So Im prob going to do this tomorrow AM. Only thing is, I have factory fog lights. I really dont care if I cut them out because I would like to relocate them on the bumper somewhere anyways. My question is this, do I have to remove the wheel liner to get the windshield washer bottle out?
Author:  jason thompson [ Fri Jun 29, 2007 6:41 pm ]
Post subject:  Re: Front fender trimming
jdumont wrote:
So Im prob going to do this tomorrow AM. Only thing is, I have factory fog lights. I really dont care if I cut them out because I would like to relocate them on the bumper somewhere anyways. My question is this, do I have to remove the wheel liner to get the windshield washer bottle out?



why are you doing this?
are you running bigger than 245/75's?
I did some fancy melting and got no rub with 245/75's I moved nothing but the wireing for the fogs and that was to get it out of the heat
Author:  jdumont [ Sun Jul 01, 2007 8:06 am ]
Post subject: 
Im doing it because I like the way it looks on others that have done it here. I do get a little rub at full lock. I did all the cutting and bottle removal yesterday. All I need now is the replacement bottle that will fit in the engine compartment. The one at Auto Zone seemed too big to fit in the passenger side. Anyone have any suggestions? Ill post some pics today or tomorrow of how the bumper came out!
Author:  KJ04 [ Sun Jul 01, 2007 9:51 am ]
Post subject: 
jdumont wrote:
Im doing it because I like the way it looks on others that have done it here. I do get a little rub at full lock. I did all the cutting and bottle removal yesterday. All I need now is the replacement bottle that will fit in the engine compartment. The one at Auto Zone seemed too big to fit in the passenger side. Anyone have any suggestions? Ill post some pics today or tomorrow of how the bumper came out!


The replacement bottle from Auto Zone is actually a Universal 2.5qt. coolant recovery bottle with a wire holder.
Is this what you were looking at?
It fit fine on my 04, just had to add about 15" of electrical wire, the hose was good to go, and just drilled the 2 holes for the pump and sensor and pluged the overflow with rtv and a screw.

Image
Author:  jdumont [ Mon Jul 02, 2007 6:42 am ]
Post subject: 
Yea I saw that one from Auto Zone yesterday but I didnt think it would fit. Do you have the cruise control module right also...? Im going to go out in the parking lot this AM and snap some pics. I think it came out great....
Author:  Blue KJ in PA [ Mon Jul 02, 2007 7:56 am ]
Post subject: 
Wally World also has the same overflow bottle if you are there.
Author:  jdumont [ Mon Jul 02, 2007 8:32 am ]
Post subject: 
Here is a prelim pic. Ill take some more tonight and post em up... Which link in imageshack am I supposed to pic to insert the image directly in the post? I have no problems with Photobucket at home but its blocked here at work...


http://img165.imageshack.us/img165/4845/dscn4258no1.jpg
Author:  jdumont [ Mon Jul 02, 2007 8:36 am ]
Post subject: 
Nevermind, got it...


Image
Author:  jdumont [ Mon Jul 02, 2007 6:36 pm ]
Post subject: 
So here is a pretty good pic of whats going on over here.....

Image
Author:  Tokyojoe [ Mon Jul 02, 2007 8:56 pm ]
Post subject: 
Since your flares and lower panel are black, I think a black front bumper fascia would look better. Most likely same for the rear bumper fascia.
Author:  priell3 [ Mon Jul 02, 2007 9:21 pm ]
Post subject: 
That bumper mod looks pretty good.
Author:  riptricket [ Mon Jul 02, 2007 10:56 pm ]
Post subject: 
did u have the flares line-x-ed?
Author:  jdumont [ Tue Jul 03, 2007 7:06 am ]
Post subject: 
The flares and doors are Herculined. It wasnt too hard to do, just clean and scuff more than you think you should and youll be fine. I have been thinking of doing the bumpers too. Ill prob do them in a few weeks I suppose when I get the itch again.... thanks for the comments.
Author:  Blue KJ in PA [ Tue Jul 03, 2007 8:59 am ]
Post subject: 
Tokyojoe wrote:
Since your flares and lower panel are black, I think a black front bumper fascia would look better. Most likely same for the rear bumper fascia.


I was thinking same thing...for his KJ and my own... :D
Author:  riptricket [ Tue Jul 03, 2007 10:27 am ]
Post subject: 
how many cans did you go through?
Author:  jdumont [ Tue Jul 03, 2007 8:04 pm ]
Post subject: 
I used just about two of the smaller $30 cans. I actually just checked to see if i could touch up some spots and the remains of the 2nd can were dry.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/