| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| New CB antenna location... http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=23413 |
Page 1 of 1 |
| Author: | riptricket [ Mon Aug 13, 2007 5:34 pm ] |
| Post subject: | New CB antenna location... |
I bount this from radioshack...http://www.radioshack.com/product/index.jsp?summary=summary&techSpecs=techSpecs¤tTab=techSpecs&cp=&custRatings=custRatings&features=features&accessories=accessories&productId=2102429&support=support&tab=summary and attached it to my RL license plate bracket... to look like this... 
and who cares if it is off-centered... it looks bad stupid |
|
| Author: | ATXKJ [ Mon Aug 13, 2007 5:48 pm ] |
| Post subject: | |
Can you open the rear glass? |
|
| Author: | riptricket [ Mon Aug 13, 2007 5:49 pm ] |
| Post subject: | |
yes, all the way up and down! |
|
| Author: | riptricket [ Tue Aug 14, 2007 2:47 pm ] |
| Post subject: | |
alright... i was driving down the highway yesterday and all of a sudden, i could see the antenna reallly swaying to the left and right. it is not tight enough. i put on some grippy stuff, but that didn't make it any better... anyone know of anything else i could put between the piece and the RL license plate bracket to make it from moving 100%? Thanks~ |
|
| Author: | tommudd [ Tue Aug 14, 2007 3:04 pm ] |
| Post subject: | |
duct tape, electrical tape, peanut butter....... 
Tom |
|
| Author: | WoodysKJ [ Tue Aug 14, 2007 3:07 pm ] |
| Post subject: | |
Turn the plate with the notch in it 90 degrees and tighten the hell out of it. |
|
| Author: | Rockjeep [ Tue Aug 14, 2007 6:35 pm ] |
| Post subject: | |
remember the mount is part of your ground plane. Needs metal to metal contact. |
|
| Author: | ATXKJ [ Tue Aug 14, 2007 8:02 pm ] |
| Post subject: | |
grind/file a small flat on the license plate shaft - then drill a small hole through the antenna bracket to add a setscrew that stops on the flat. |
|
| Author: | riptricket [ Fri Oct 05, 2007 10:42 am ] |
| Post subject: | |
so i tried the duct and electrical tape and still sways when driving... i don't know what else to do! anyone? |
|
| Author: | WoodysKJ [ Fri Oct 05, 2007 11:08 am ] |
| Post subject: | |
Did you try taking the groved plate off and rotating it 90 degrees so the grove is perpendicular to the shaft? Do that an tighten the crap out of it. You might also akte some vise grips to the shaft and clamp down on it and put some tooth marks in the metal, giving the mount some teeth to grip to and not a smooth surface. The last try would be to get it all tightened up and then drill through the mounts, both of them and then tapping threads so a small screw passes through all or at least half of the antenna mount and the plate bracket. Kind of a lock or set screw. 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|