| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| What size conduit nuts for clevis lift? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=29219 |
Page 1 of 1 |
| Author: | BeepBeepJeepJeep [ Tue Feb 05, 2008 10:32 am ] |
| Post subject: | What size conduit nuts for clevis lift? |
While I have my entire suspension apart I figure I might as well add another ring to my clevis lift (currently 3). Can someone remind me what size nuts to use? Thanks, Bill |
|
| Author: | pokefan [ Tue Feb 05, 2008 10:44 am ] |
| Post subject: | |
Tech Section... http://www.lostjeeps.com/forum/phpBB3/vie ... hp?t=15164 |
|
| Author: | Jeepjeepster [ Tue Feb 05, 2008 12:42 pm ] |
| Post subject: | |
2" Make sure you dont get UBJC after adding more. Mine was very close with just two. |
|
| Author: | BeepBeepJeepJeep [ Tue Feb 05, 2008 9:51 pm ] |
| Post subject: | |
Jeepjeepster wrote: 2"
Make sure you dont get UBJC after adding more. Mine was very close with just two. Thanks for the warning... I was getting UBJ contact and that's why my UBJs failed and that's why I have al's a-arms sitting behind me... |
|
| Author: | Jeepjeepster [ Wed Feb 06, 2008 12:25 am ] |
| Post subject: | |
BeepBeepJeepJeep wrote: Jeepjeepster wrote: 2" Make sure you dont get UBJC after adding more. Mine was very close with just two. Thanks for the warning... I was getting UBJ contact and that's why my UBJs failed and that's why I have al's a-arms sitting behind me... Ahh, youve got no worries then. 
|
|
| Author: | dloc_jeep_KJ [ Wed Feb 06, 2008 12:30 am ] |
| Post subject: | |
so where is the best place to get these?? can u get them at lowes? edit they have them online so i would guess they have them in the store.. where would they be? |
|
| Author: | tommudd [ Wed Feb 06, 2008 1:09 am ] |
| Post subject: | |
electrical section....I could say "well DUH! "' but will try and hold back  just messing with ya!
|
|
| Author: | dloc_jeep_KJ [ Wed Feb 06, 2008 1:13 am ] |
| Post subject: | |
hey im a welder not an electrician  i just hate walking all over that store to find some part that no one there ever know what im talking about. if i asked where i could find a screw driver they would walk me to the lumbar yard  .. sorry tom and thanks!!!
|
|
| Author: | tommudd [ Wed Feb 06, 2008 1:21 am ] |
| Post subject: | |
Glad I could tell you where to go to!!!!!!!!  They are hard to find at times but go to electrical section and they should have an area with different fittings, conduit nuts etc.
Now get back to welding!
|
|
| Author: | dloc_jeep_KJ [ Wed Feb 06, 2008 1:27 am ] |
| Post subject: | |
thanks... at 12:30  give me about 5 hrs (to sleep) and i will hows that
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|