1/2 inch then
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Rusty's Stut spacer... http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=29420 |
Page 1 of 1 |
| Author: | BeepBeepJeepJeep [ Mon Feb 11, 2008 10:48 pm ] |
| Post subject: | Rusty's Stut spacer... |
Will this give me 1/2" of lift or 1"?? |
|
| Author: | tommudd [ Mon Feb 11, 2008 10:48 pm ] |
| Post subject: | |
inch |
|
| Author: | BeepBeepJeepJeep [ Mon Feb 11, 2008 10:53 pm ] |
| Post subject: | |
That's freakin' awesome... I got my strut spacers today but I'm not sure I'll be able to fit both the 4 clevis rings and the strut spacer in there... might have to take one (or sadly two) out.. |
|
| Author: | dloc_jeep_KJ [ Mon Feb 11, 2008 10:55 pm ] |
| Post subject: | |
are u talking about the Rustys strut spacer. i thought they were just 1/4" thus giving u 1/2" lift. i could be way wrong on this though. |
|
| Author: | BeepBeepJeepJeep [ Mon Feb 11, 2008 10:56 pm ] |
| Post subject: | |
dloc_jeep_KJ wrote: are u talking about the Rustys strut spacer. i thought they were just 1/4" thus giving u 1/2" lift. i could be way wrong on this though.
Yeah that's what I'm talking about... Edit: Just measured it, it's 1/4"... |
|
| Author: | tommudd [ Mon Feb 11, 2008 11:12 pm ] |
| Post subject: | |
1/2 inch then
|
|
| Author: | dloc_jeep_KJ [ Mon Feb 11, 2008 11:39 pm ] |
| Post subject: | |
wow i was right  thats a first  the new Simon says  JK
|
|
| Author: | BeepBeepJeepJeep [ Mon Feb 11, 2008 11:48 pm ] |
| Post subject: | |
dloc_jeep_KJ wrote: wow i was right
thats a first the new Simon says JK
|
|
| Author: | renegadekj [ Mon Feb 11, 2008 11:48 pm ] |
| Post subject: | |
BeepBeepJeepJeep You may have to drill the holes on the strut plates to line up with your stock strut plate bolt pattern. You should beable to get 3 nuts and the 1/4" strut plate in there. Beaware of your cv angles, I did this lift with OME med's and I'm pretty much maxed out. Josh |
|
| Author: | BeepBeepJeepJeep [ Mon Feb 11, 2008 11:51 pm ] |
| Post subject: | |
renegadekj wrote: BeepBeepJeepJeep You may have to drill the holes on the strut plates to line up with your stock strut plate bolt pattern. You should beable to get 3 nuts and the 1/4" strut plate in there. Beaware of your cv angles, I did this lift with OME med's and I'm pretty much maxed out.
Josh Thanks 
Bill |
|
| Author: | BeepBeepJeepJeep [ Tue Feb 12, 2008 12:01 am ] |
| Post subject: | |
I've decided these are not worth the hassle and I've tossed them into the For Sale section... |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|