Need to rivit my fenders back on and don't wanna use the plastic ones what size and width rivits do I use?

_________________
'02 Liberty Limited 4x4
-Selec Trac
-MTR's 245/75-16
-Rock Lizard Super Skink Sliders(custom)
-Engine skid, Skidrow Transmission skid
-4" Lift - JBA 4.5 Gen A-arms
Installed@165,920k
Pilot lights on cowl
Engine replacement at 175k

alllrighty then, anyone have the part number for the 7/16th plastic push rivits?

_________________
'02 Liberty Limited 4x4
-Selec Trac
-MTR's 245/75-16
-Rock Lizard Super Skink Sliders(custom)
-Engine skid, Skidrow Transmission skid
-4" Lift - JBA 4.5 Gen A-arms
Installed@165,920k
Pilot lights on cowl
Engine replacement at 175k

I think this question came up in the past & I remember there was a part # there. I think it was in the General Discussion forum & it definitely was a while ago. I will try to look for it when I get home but no promises.

Sent using Tapatalk

_________________
Mike D.
2011 Brilliant Black KK Renegade 4x4 (New addition)


2003 Atlantic Blue KJ 2WD

http://auveco.com/download/pdf/471.pdf
Check this page. I don't know which model you need but it's most likely one of these.
For a WJ but some info could be useful.
http://www.wjjeeps.com/grilles/grillesrem.htm#RIVETSET
Jeff

_________________
2006 Black Sport 4x4
2" Class 4 Reese Hitch
Huskies and Igees
Full Mopar Skids
Yakima roof rack system
ARB bumper
Hella 500's
Rock Lizard Super Skinks
Frankenlift Premium II
GY Duratracs 245/70/16 AT's on Cragar Soft 8s
JBA 4.5 A-arms
Cobra Classic CB

I picked some up from the dealer for my right front fender flare – BUT – I was told by the dealer that I need a special rivit gun as a normal one would crack the plastic rivits. Does anyone know if there is any truth to that? Andrew – I’ll check to see if there is a part tag on them but I'm pretty sure I just picked them up individually and put them in a brown bag.

_________________
(Formerly just “scoobysnax”) '04 Liberty Limited - 245/70/16 Firestone Destination AT's, Mopar tow hooks, Draw-Tite Class IV hitch, Skid Row Engine & Transmission Skids, Mopar T-Case & Gas Tank Skids, Extended Breather Tubes, Red Top Optima, Sylvania Silver Star head lights, Hella 500FF bumper mounted driving lights

For push rivets go to Lowes they have several styles of push rivets.

_________________
02 Sport,Frankenlifted,JBA arms,31/11.50/15 LTB,Aussie locker,204,000m

http://www.sjdiscounttools.com/

Yes you need a plastic rivit install tool as they require a longer stroke to set the plastic rivit and a larger barrel to accommodate the diameter of the rivit shank.

20 bucks from the above.

I see you already got hosed by the dealer for the rivits. I will see what the part number is from autobody supply on the rivits I have. They work fine, slightly smaller head although I think they had both sizes.

_________________
2004 KJ Limited
Frankenlift II
Eaton "E" Locker front
Detroit Locker rear
Boulder Bars
Procomp alloys 16 x 8 with 4" back spacing
BFG AT's 235 x 70 x 16

Both lowe's and HD have the Hilman? push rivets, as many times as I've had my flares on and off, I've only had to replace 2 of them

_________________
03 Renegade (Black)
177k miles 3.7L gas - 45RFE
Command Trac / 4.10s
Lift: ft. 790+ rr. JBA4+
The last of the TrailReady Front&Rear Bumpers and TR Rock Rails
Jarhead Offroad light covers
31x10.5R15 RedLetter Grabbers on Blackrock Dunes
L.O.S.T #KD098632