LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Oil Pressure Sender
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=58481		 Page 1 of 1
Author:  audiboy86 [ Tue Jan 25, 2011 5:20 pm ]
Post subject:  Oil Pressure Sender
Well today i was going down the road in my girlfriends jeep and noticed her oil light stayed on. So i made her pull over and checked it twice at that. It isnt low and i just changed it a few days ago. So i think it is the pressure sending unit and i need to know where it is and a part number would be great. I think it is somewhere near the filter but if someone could please tell me for sure and make my day alot easier. Aslo as you can tell i am a CRD guy working on a V-6 gasser so i am out of my element :wink: .
Author:  STINGN [ Tue Jan 25, 2011 5:24 pm ]
Post subject:  Re: Oil Pressure Sender
its above the oil filter. you need to unhook the electrical piece and then take it off. i dont know HOW to take it off because it is on there pretty darn good. taking the oil filter off will help a lot tho
Author:  audiboy86 [ Wed Jan 26, 2011 9:41 am ]
Post subject:  Re: Oil Pressure Sender
I will have a look at it tonight when i get home and do a wirte up on how i got it off and the location. It just sucks though because i just changed the oil :furious: and if i have to remove the filter :furious: :banghead: knew i should of fixed that before i changed the oil.
Author:  Joe Romas [ Wed Jan 26, 2011 12:14 pm ]
Post subject:  Re: Oil Pressure Sender
This has been brought up before and as I recall the sender is a common one avalable at Advanced or Autozone.
Here's a link to what I found at AutoZone.
http://www.autozone.com/autozone/parts/ ... o1cqZ9ciau

Joe
Author:  audiboy86 [ Thu Jan 27, 2011 9:32 am ]
Post subject:  Re: Oil Pressure Sender
Thank you i looked at it last night but didn't have any of my sockets to try :banghead:. And thanks for that link i will be going to pick one up asap it is driving me up the wall looking at the light everytime i get in her jeep.
Author:  bgcarl01 [ Tue May 03, 2011 2:23 pm ]
Post subject:  Re: Oil Pressure Sender
I think it's just over an inch, like an inch and 1/16th. And if your my size you can barely get to the filter from underneath the jeep, so getting to the switch is not happening. ( I'm thinking there should be , "Jeep Liberty Filter change Pose." for yoga. ) I changed mine by quickly removing the battery, under hood fuse block and battery tray. Much, much more room this way. Had to use my wife's hand mirror to make sure I was undoing the clip correctly. I also took the serpentine belt off to allow room for a universal joint, extension, and then my ratchet fit in between fan and pump. Nothing like Chrysler cramming that stuff in there alltogether. What ever happened to working on a v-8 with so much room in the engine bay you can sit on the inner fenders and work on the motor?
Author:  bhc04 [ Tue May 03, 2011 5:36 pm ]
Post subject:  Re: Oil Pressure Sender
Careful when you put the new one on. Don't torque it down to tight or you may damage it. Just nice and snug is good.
Author:  sidewayskj [ Wed May 04, 2011 11:04 am ]
Post subject:  Re: Oil Pressure Sender
Yes it is an inch and a 1/16 deep socket. Serp belt off can help also. Done my sensor twice. Napa also carries them.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/