| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| My alignment is maxed out http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=65261 |
Page 1 of 1 |
| Author: | Kks03kj [ Sat Feb 18, 2012 4:20 pm ] |
| Post subject: | My alignment is maxed out |
So my alignment is maxed out on uca and was wondering if there is a extender bolt or something besides rro uca or jba's Kinda newto this stuff  Running a 03 Libby with 3" lift And also looking into getting rid of the front spacer what's a good 3" setup for the front Thank you |
|
| Author: | tommudd [ Sat Feb 18, 2012 6:17 pm ] |
| Post subject: | Re: My alignment is maxed out |
No extender bolts good alignment person should be able to get it close enough to where it will handle and tires will wear good Don't even think of RRO UCAs , JBAs only What spacer lift do you have and where do you sit ( measure from middle of wheel to bottom of flare in the front) |
|
| Author: | Kks03kj [ Sat Feb 18, 2012 7:09 pm ] |
| Post subject: | Re: My alignment is maxed out |
Rough country 3" and I'll measure When the its back at home lol |
|
| Author: | tommudd [ Sat Feb 18, 2012 7:25 pm ] |
| Post subject: | Re: My alignment is maxed out |
get some OME 927 springs in front good set of either Bilstein or OME shocks , then add some teraflex front bumpstops. The springs will give you about 2.25-2.5 inches of lift if you want 3 add a 1/4 inch top plate or 3/8 inch clevis and you'll have the 3 inches you want Then proceed to the rear 
|
|
| Author: | All3Sports [ Sat Feb 18, 2012 7:26 pm ] |
| Post subject: | Re: My alignment is maxed out |
Wont be at 3 inches for long with that lift. |
|
| Author: | Kks03kj [ Sat Feb 18, 2012 7:50 pm ] |
| Post subject: | Re: My alignment is maxed out |
All3Sports wrote: Wont be at 3 inches for long with that lift. Yea it doesn't look like it is anymore I ordered bumps stops yesterday |
|
| Author: | Kks03kj [ Sun Feb 19, 2012 12:11 am ] |
| Post subject: | Re: My alignment is maxed out |
tommudd wrote: No extender bolts good alignment person should be able to get it close enough to where it will handle and tires will wear good Don't even think of RRO UCAs , JBAs only What spacer lift do you have and where do you sit ( measure from middle of wheel to bottom of flare in the front) Do you know what the stock height is? |
|
| Author: | Kks03kj [ Sun Feb 19, 2012 12:28 am ] |
| Post subject: | Re: My alignment is maxed out |
tommudd wrote: No extender bolts good alignment person should be able to get it close enough to where it will handle and tires will wear good Don't even think of RRO UCAs , JBAs only What spacer lift do you have and where do you sit ( measure from middle of wheel to bottom of flare in the front) right now there sitting about at 21 all around |
|
| Author: | tjkj2002 [ Sun Feb 19, 2012 8:30 am ] |
| Post subject: | Re: My alignment is maxed out |
Kks03kj wrote: right now there sitting about at 21 all around So your only at 2" of lift over stock. |
|
| Author: | tommudd [ Sun Feb 19, 2012 9:15 am ] |
| Post subject: | Re: My alignment is maxed out |
And at 21 you should have no problems getting an alignment done unless you have other issues or someone that doesn't know how to align one ( even with stock UCAs) |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|