LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

KJ Rear Bumper FOR SALE ORDER NOW !!
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=79399		 Page 1 of 3
Author:  tommudd [ Thu Jun 19, 2014 7:50 pm ]
Post subject:  KJ Rear Bumper FOR SALE ORDER NOW !!
We are now ready to start. The design will be like shown below EXCEPT without the holes across the face. There will still be holes on the lower section. There is one design only, no custom one offs.
I had to order 10 to start. 2 are spoken for already, so I have 8 that will be for sale. These are all laser cut and are looking great.
Any orders paid in full by the 15th will also get a free set of recovery shackles on the house. Price for the bumper is $695.00, with LED lights $775.00 OK, ALL PRICES PLUS SHIPPING
Retail is going to be 960.00
Shipping will be approximately 3 weeks from the date you order.
IF INTERESTED PM ME AND I WILL SEND YOU MY PAYPAL ACCOUNT INFORMATION.
THESE ARE BEING SOLD ONLY THROUGH MUDDS GARAGE :wink:


The bumper will weigh 70lbs with hardware, and will come with LED cube lights included ( you can see where they will mount on either side )
The tire carrier will come soon. The carrier will be
adjustable in height and angle and allow mounting of Rotopax gas can
setup. It will not come with a hitch, but the
factory hitch bolts right up under it if needed. The bumper is 1/8", and
the mounts are 1/4" with 3/4" shackle tabs. Pricing is yet to be determined.
I cannot give out any other information right now but this is the same place that is working on the front conversion bracket for KJ/KK to mount TJ/JK wrangler front bumpers, as well as new designed roof racks and sliders and front bumper that will have the same
theme as the rear bumper shown here.
So thoughts/comments ...............................I know you have them :wink: :lol:
Image
Image
Image
Image
Image
Image
Broke down for easier shipping than most other bumpers out there
Image Stock spare tire carrier can still be used if you want
Image
Author:  NewOldTimer [ Thu Jun 19, 2014 8:06 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
My only question is; When will it be available???

That is exactly what I need. Nothing fancy, or heavy. Just steel out back.
I presume the LED's are for reverse lights...
Author:  allyrand [ Thu Jun 19, 2014 8:13 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
Looks awesome Tom, I am going to show this to a few people here. I bet they would be on board
Author:  tommudd [ Thu Jun 19, 2014 8:15 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
NewOldTimer wrote:
My only question is; When will it be available???

That is exactly what I need. Nothing fancy, or heavy. Just steel out back.
I presume the LED's are for reverse lights...


Hoping will be available soon
and yes the LED Pods will be for back up lights
Author:  501 [ Thu Jun 19, 2014 8:23 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
Really nice looking, simple.

Would be nice if you could by the basic bumper, then add the tire carrier, gas can, etc.at a later date if you want or not at all.
Also would be nice if they make a front bumper in the same design too.

One thought: Is there any wind noise because of the holes? (Thinking of the noise I use to get when I used uni-strut for cross bars.)
Author:  tommudd [ Thu Jun 19, 2014 8:31 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
501 wrote:
Really nice looking, simple.

Would be nice if you could by the basic bumper, then add the tire carrier, gas can, etc.at a later date if you want or not at all.
Also would be nice if they make a front bumper in the same design too.

One thought: Is there any wind noise because of the holes? (Thinking of the noise I use to get when I used uni-strut for cross bars.)


DARYL, WE'LL CONNECT THE FRONT AND REAR BUMPERS WITH TUBES THAT WAY THE WIND WILL FLOW RIGHT THROUGH :ROTFL:

Whoops sorry for the caps :oops:
Author:  501 [ Thu Jun 19, 2014 9:16 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
tommudd wrote:
501 wrote:
Really nice looking, simple.

Would be nice if you could by the basic bumper, then add the tire carrier, gas can, etc.at a later date if you want or not at all.
Also would be nice if they make a front bumper in the same design too.

One thought: Is there any wind noise because of the holes? (Thinking of the noise I use to get when I used uni-strut for cross bars.)


DARYL, WE'LL CONNECT THE FRONT AND REAR BUMPERS WITH TUBES THAT WAY THE WIND WILL FLOW RIGHT THROUGH :ROTFL:

Whoops sorry for the caps :oops:


We could put holes in the tubes and cork plugs on electronic controlled hinges so that when driving down the road one could hit buttons on the center of the steering wheel and play music!! :ROTFL:
Author:  JdubKJ03 [ Thu Jun 19, 2014 9:42 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
Looks good, So bolting those bumper brackets on with a hitch and mopar skid plate will work? Longer bolts required?
Author:  profdlp [ Thu Jun 19, 2014 10:04 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
501 wrote:
...We could put holes in the tubes and cork plugs on electronic controlled hinges so that when driving down the road one could hit buttons on the center of the steering wheel and play music!! :ROTFL:

Brand new for 2015 - the innovative Jeep Calliope:

http://en.wikipedia.org/wiki/Calliope_%28music%29
Author:  silverkk [ Thu Jun 19, 2014 10:56 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
Looks like it may fit a kk
Author:  WolverineFW [ Thu Jun 19, 2014 11:22 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
Are they going to make a version without all the speed holes? lol

Not sure I am digging that look.
Author:  MoD [ Fri Jun 20, 2014 1:48 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
If they need a supplier for the led pods, you know where to go ;)
Author:  fortx4 KJ [ Fri Jun 20, 2014 6:37 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
I'm digging the design but don't like the holes in the upper middle section or the led square holes. Its nice to see r&d going into a libby.
Author:  John3:17 [ Fri Jun 20, 2014 7:59 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
I'm liking it. Had to set back and use my imagination a little and carry the hole theme a little further. Accessories, Soft 8's , a front bumper with similar design etc. etc. . Good option for keeping the Libby light but still have steel bumpers.
Author:  tommudd [ Fri Jun 20, 2014 9:39 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
WolverineFW wrote:
Are they going to make a version without all the speed holes? lol

Not sure I am digging that look.


Maybe....., possibly could do the center section without the holes, but sides will remain, with the design of the front bumper design having the same overall look and being part of the look we are going for, some have to remain. Otherwise I think they will just look like others, trying to set these apart with a " new " look not seen on KJs up till now.
I guess I'm old and have always really liked the "speed holes". I remember a lot of the old drag racing cars back in the 60s having those punched in and they looked bad a**!! Someone said they looked Rat Rodish but here they have been doing this for years. Rat Rods are just reviving an old tradition. So until more items are welded up just imagine front and rear bumpers with the same theme :wink:
Author:  tommudd [ Fri Jun 20, 2014 9:40 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
John3:17 wrote:
I'm liking it. Had to set back and use my imagination a little and carry the hole theme a little further. Accessories, Soft 8's , a front bumper with similar design etc. etc. . Good option for keeping the Libby light but still have steel bumpers.



See you're getting the overall theme now :ROTFL:
Author:  tommudd [ Fri Jun 20, 2014 9:42 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
fortx4 KJ wrote:
I'm digging the design but don't like the holes in the upper middle section or the led square holes. Its nice to see r&d going into a libby.


Have to keep the R&D going, Just found my Step dad an 05, I would like to have a couple more before the year is out. My goal is to have an 02-03-04, :wink: :roll: :wink: So what else are we to do but keep trying to keep the KJs alive !! :ROTFL:
Author:  WolverineFW [ Fri Jun 20, 2014 10:20 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
tommudd wrote:
WolverineFW wrote:
Are they going to make a version without all the speed holes? lol

Not sure I am digging that look.


Maybe....., possibly could do the center section without the holes, but sides will remain, with the design of the front bumper design having the same overall look and being part of the look we are going for, some have to remain. Otherwise I think they will just look like others, trying to set these apart with a " new " look not seen on KJs up till now.
I guess I'm old and have always really liked the "speed holes". I remember a lot of the old drag racing cars back in the 60s having those punched in and they looked bad a**!! Someone said they looked Rat Rodish but here they have been doing this for years. Rat Rods are just reviving an old tradition. So until more items are welded up just imagine front and rear bumpers with the same theme :wink:


I think if you it had the center piece without all the holes and left the side pieces as they are it would look better IMHO. But that is just me. lol
Author:  tommudd [ Fri Jun 20, 2014 11:35 am ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
I should of clarified some more on the speed holes, the bottom row will remain regardless, the ones on the face could be omitted if the customer wants it like that. Everything that is being planned will have speed holes so have to stay with that theme
Author:  -XR- [ Fri Jun 20, 2014 11:25 pm ]
Post subject:  Re: New KJ Rear Bumper In the Works !!!
I like it. Buuuuuttttttttttttttttt.............what if I have the tow hitch???????
Page 1 of 3 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/