LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Q's on light bar Install ( found a neat solution)
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=1&t=8120		 Page 1 of 1
Author:  Fouros [ Tue May 02, 2006 12:35 am ]
Post subject:  Q's on light bar Install ( found a neat solution)
ok guys i have just recieved my Rene Light bar

and i have a couple of questions, I have an export model delivered in Australia and when i pulled some of the trim back i found THIS

Image




ok i had forgotten it was there when i installed my driving lights

un plugged

Image




now the wiring loom that came with the bar has this

Image





the switch that came with the light bar plugs straight into this mystery plug behind the dash

my fuse box under the bonnet ( Hood) has the light bar fuse already there



can anybdy check thier 04 sport and see if this is just an export thing or if it is common to all 04 KJ's and what would happen if i try and plug it in on a dry run


could i cook the electrics?????
Author:  4wdParakeet [ Tue May 02, 2006 1:07 am ]
Post subject: 
Fouros it's pretty common for auto manufatures to put connections for higher models in the lower models. They do that so that they can cut down on the number of different parts, make them more cookie cutter like and make more, and that also makes it so that adding on is plug and play. I have the U-Connect Handsfree kit and it was all plug into plugs that were there. My Dad when he bought his Intrepid found a set of 300M leather, power seats and they bolted right in. All the plugs for the pass seat where already there even though it was oem with a manual seat. I would say you have little chances of frying something. Just make sure that all the fuses are good and if you are really worried about it go to the next fuse size down and plug that in that way if it does want to blow something it will blow that smaller fuse faster than the larger one.


Parakeet
Author:  Fouros [ Tue May 02, 2006 3:21 am ]
Post subject: 
now the interesting thing


is there a wiring diagram for the KJ anywhere i can get my hands on so i can see if the power lead from the light bar can be connected to a lead under the dash???????
Author:  ShadE [ Tue May 02, 2006 1:21 pm ]
Post subject: 
When I put on my light bar, I got a wireing harness like yours. The plugs that are in the spots for the lightbar harness you need to take out and insert into the back of the lightbar harness fuse wireing. I think this adds to the max voltage allowed through the fuse.

I have no idea whats up with the plug in the dash peice. It gave me a new trim peice with a whole cut out of it. I simply incerted the switch and plugged it in.

The wireing harness went through my brake garmet and connected to my battery. If you want a lead from the battery, they are the largest red and black wires in the main harness under the dash...


And have fun drilling holes in the top of your Libby!!! lol
Author:  Fouros [ Mon May 08, 2006 2:52 am ]
Post subject: 
can any of you guys with a rene that has a factory fitted light bar check something for me


look at the harness that comes from the light bar and see where it runs to inside the cabin,

i am thinking that the connector is somewhere in my loom ang i just gotta find it,


well the relay is in the box under the hood and the fuse is in the fuse box so its gotta be there somewhere
Author:  Jeep Dawg [ Thu May 11, 2006 12:30 pm ]
Post subject:  light bar
Hey ShadE

What did you have to do to install your light bar?
How long did it take and do you hvae pictures and tips?
I am about to buy one and see what kind of trouble that I am about to get my self into.
Author:  ShadE [ Thu May 11, 2006 2:36 pm ]
Post subject:  Re: light bar
Jeep Dawg wrote:
Hey ShadE

What did you have to do to install your light bar?
How long did it take and do you hvae pictures and tips?
I am about to buy one and see what kind of trouble that I am about to get my self into.

It was all pretty staight-forward. It comes with some crappy instructions, but it is do-able. it took me around 4 hours as i recall, but i worked in a car electronics shop installing stuff for a while. I would figure a good saturday, 4-8 hours. I didn't get any pics.

tips:
1. measure 3 times, line up your light bar, measure again, then drill.
2. use brand new bits and a nice drill, you don't want to punch through your head-liner.
3. pick a good gasket caulk and use it very liberally. I covered every hole and bolt-head.

other than that, good luck! and remember, If you screw it all up, an auto shop can fix it. :lol:
Author:  Jeep Dawg [ Fri May 12, 2006 9:11 pm ]
Post subject: 
Kool thanks man

I screw up alot of doo doo. I know how to kinda cover a big OH doo doo!!!
lol
Author:  Fouros [ Mon May 29, 2006 11:17 pm ]
Post subject: 
bump try again

can any of you guys with a rene that has a factory fitted light bar check something for me


look at the harness that comes from the light bar and see where it runs to inside the cabin,

i am thinking that the connector is somewhere in my loom and i just gotta find it,


well the relay is in the box under the hood and the fuse is in the fuse box so its gotta be there somewhere
Author:  Fouros [ Tue May 30, 2006 2:22 am ]
Post subject: 
Woot Woot


i just did something and it didnt fry the KJ ,




i connected up the light bar for a dry run and bugger me,

i used the plug that was behind the dash already on my export kj connected the white wire with the brown stripe from the light bar to the white wire with the brown stripe coming from the back of the mystery plug, then earthed the other one hit the switch and IT FREAKING WORKS I even get the light bar illumination warning in the dash lighting up The BCM recognises it




sooooooooooooo happy :D
Author:  Stuhlie [ Tue May 30, 2006 2:41 am ]
Post subject: 
Great Job Fourus ! 8)
Author:  Fouros [ Tue May 30, 2006 3:05 am ]
Post subject: 
and they work with the parking lamps on or with my High beam on so very soon i will have


light bar (parkers or high beam )
fogs ( that work on high beam )
Driving lamps ( high beam only)


he he when i drive at night the birds will wake up and think its morning :D


Image

dash from my KJ Sport even the BCM knows its there

Image


i will do a full write up with picks when i do the real install


Fouros
Author:  Fouros [ Thu Jun 08, 2006 8:13 pm ]
Post subject:  FOUND IT
ok for those punters wondering well i found the light bar harness that i knew would be there :)

if you remove the Grab handle trim from the Left hand Side of the KJ at the bottom of the A pillar there is a socket that is being un used

Image

this is the FACTORY wiring harness for the Light Bar

you will also find behind the Trim that goes between the steering wheel and the drivers door a plug like this

Image

the switch that comes with the light bar kit plugs into it like so

Image


from there you connect the harness from the light bar

Image

to the plug as shown in the first picture like so

Image

and your done this is the result


Image


Image

so it looks like all that extra crap that comes with the light bar kit is surplus to requirements , Unless being an export KJ I just got Lucky

does anybody want to check thier Limited or sports to see if you have the same harness in your kj's


now i have to drill holes in my roof :shock:
Author:  ShadE [ Thu Jun 08, 2006 8:40 pm ]
Post subject: 
I needed all of the harness peices for the install into my limited. It was completly baren of any pre-installed wiring.
Author:  Fouros [ Thu Jun 08, 2006 11:30 pm ]
Post subject: 
bugger

i wonder if it just an export KJ thing
Author:  liberty 4 all [ Thu Jun 08, 2006 11:51 pm ]
Post subject: 
Fouros wrote:
bugger

i wonder if it just an export KJ thing


Yes...it is because I have none of the factory wiring in my 03 sport. I have the light bar installed on the roof but I'm trying to get the rest of the wires from the dealer. The fun of buying used...and I thought I would save some money boy was I wrong. I could have bought a new one already from what I bought and I'm still missing some wires. Remember when you drill the holes in the roof use sharp bits and lots of sealer after it's in place.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/