Long time no post. So 6 years ago I put in a OME lift on my 03 KJ. My passenger side axle needed to be replace last month. Since then the clip had popped 3 times. The axle keeps popping out. The shop is covering it but cannot figure out why it is happening. The drivers side has been fine. Any idea why it keeps coming undone.

_________________
Benny Migs
03 Black Sport
Front OME HD Coils Struts 1/2inch clevis lift, Rear OME 132L OME HD Coils 2 ISO upper pads
30x9.5x15 General Grabbers AT2 on Craiger Soft 8's 15x7 4" BS
safari rack, super nerfs, Rear Hitch, Front ARB Bumper , JBA A-Arms




http://www.BennyMigsPhoto.com

Rear axle ?

_________________
U.S. Army Retired

Sorry. Front

_________________
Benny Migs
03 Black Sport
Front OME HD Coils Struts 1/2inch clevis lift, Rear OME 132L OME HD Coils 2 ISO upper pads
30x9.5x15 General Grabbers AT2 on Craiger Soft 8's 15x7 4" BS
safari rack, super nerfs, Rear Hitch, Front ARB Bumper , JBA A-Arms




http://www.BennyMigsPhoto.com

It might be too short.
I don't know what the exact length should be but it should match the old one.
Others have reported getting a replacement CV axle from a local auto parts store and it not being the correct length.

_________________
U.S. Army Retired

Got mine at Autozone and have had nothing but problems. They have been nice enough to work with me on a solution to get it resolved though

Sent from my HTC One M9 using Tapatalk

_________________
2008 Black Liberty Sport 4X4 - Red and Black wheels and trim - Painted headlight bezels - Magnaflow Exhaust.

Been posted many many times over the years that the ones fro flatozone and other such places are usually too short, will work somewhat OK on a non lifted but not on a lifted KJ/KK
NAPA rebuilts are the only ones I will install due to that very fact.
But thats the problem, they are too short

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

Ditto on Tom's advice

Had the same problem from 'PartSource' axles (basically a car/truck focused Canadian Tire). Popped out three times for me and on the last time, ground the splines down...not returnable.

Swapped in a known good OEM axle and it's all good again.

_________________
03 KJ Sport - black
4xGuard engine skid
235/85/16 Hankook ATM
OME 927/Ironman, 1/4" plate, 3-ring clevis 21.5"
OME 948/OME + 2 Iso's Rear 22"
JBA UCAs
Bumper and winch
2x5 rockers/steps
Dynomax Ultra-Flo Welded
Custom pinstriping
Custom rear interior shelf
SS drop table
Soon:
Rear bumper
WRX seats
All the skids

Ok so after he 3 rd pop. We just got one from Jeep and so far so good. Thanks for the help guys.

_________________
Benny Migs
03 Black Sport
Front OME HD Coils Struts 1/2inch clevis lift, Rear OME 132L OME HD Coils 2 ISO upper pads
30x9.5x15 General Grabbers AT2 on Craiger Soft 8's 15x7 4" BS
safari rack, super nerfs, Rear Hitch, Front ARB Bumper , JBA A-Arms




http://www.BennyMigsPhoto.com