| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Arb bull bar for 2002 http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=113&t=58562 |
Page 1 of 1 |
| Author: | SuckerPunch [ Thu Jan 27, 2011 9:32 pm ] |
| Post subject: | Arb bull bar for 2002 |
Where is the best place to get ARB bull bar for a 02 kj? Also, is this a do it yourself job as I believe or something for a shop? |
|
| Author: | tommudd [ Thu Jan 27, 2011 10:09 pm ] |
| Post subject: | Re: Arb bull bar for 2002 |
Most anywhere that sells ARB can get them in, a lot depends on shipping etc. Just check 4 wheel drive shops near you ( like Trail Quest west side of C-bus ) and also on line Do it yourself job, if you can drill some holes, bolt things together you're good. I did mine myself, not hard at all. |
|
| Author: | steve03sport [ Thu Jan 27, 2011 10:17 pm ] |
| Post subject: | Re: Arb bull bar for 2002 |
hey tom how do you like the gtp louvers? do they work ok with lots of snow? how hard was it to cut hood |
|
| Author: | SuckerPunch [ Thu Jan 27, 2011 10:22 pm ] |
| Post subject: | Re: Arb bull bar for 2002 |
My local guy wants $1200 installed. Thought that was pretty steep. Was looking online, but I know shipping will be a bit. I'll check Trail Quest. Thanks. |
|
| Author: | tommudd [ Thu Jan 27, 2011 11:59 pm ] |
| Post subject: | Re: Arb bull bar for 2002 |
steve03sport wrote: hey tom how do you like the gtp louvers? do they work ok with lots of snow? how hard was it to cut hood The louvers work great, its sat out in rain and snow with no problems no more water than driving down the road in a heavy rain storm really. Lots of heat comes out though, cold weather you can see heat waves coming up out when stopped . Not hard to cut just used a jig saw, fun actually did wildmans as well  They are or were cheap as well |
|
| Author: | tommudd [ Fri Jan 28, 2011 12:02 am ] |
| Post subject: | Re: Arb bull bar for 2002 |
SuckerPunch wrote: My local guy wants $1200 installed. Thought that was pretty steep. Was looking online, but I know shipping will be a bit. I'll check Trail Quest. Thanks. Should be able to find one cheaper and like I said its easy to install, hardest part is cutting the fenders off and that only takes 5 minutes I'll do some checking around tomorrow for you if you need help I'll lend a hand when you do it |
|
| Author: | steve03sport [ Fri Jan 28, 2011 9:57 am ] |
| Post subject: | Re: Arb bull bar for 2002 |
tom any problems with rust or rot after cutting hood? or just put some spray paint on raw edges? |
|
| Author: | tommudd [ Fri Jan 28, 2011 1:39 pm ] |
| Post subject: | Re: Arb bull bar for 2002 |
steve03sport wrote: tom any problems with rust or rot after cutting hood? or just put some spray paint on raw edges? small tube of the touch up paint is all, kind that has the brush in it, just went around the edges. Mines been done 3 years or so now and no rust at all |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|