I am installing the rustys as well. How many conduit nuts do you have to use to get 1/2"?
Edit: Nevermind, found it in the first post. Too early.
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Installation of Rusty's coil lift + clevis/spring isolator http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=16&t=15164 |
Page 2 of 2 |
| Author: | jsc7002 [ Tue May 27, 2008 10:47 pm ] |
| Post subject: | |
daspes wrote: jsc7002 wrote: ga_repoman wrote: where can u get them?? Who sells them?? (The Rear Upper Isolator Pad) try here they are only $9 http://www.trademotion.com/partlocator/ ... atalogid=1 Same place i posted, I was going off memory on the price. oh sorry, I wasnt paying attention |
|
| Author: | jsc7002 [ Tue May 27, 2008 11:47 pm ] |
| Post subject: | |
does anyone know the p/n for the rear upper iso? |
|
| Author: | racnee [ Wed May 28, 2008 12:11 am ] |
| Post subject: | |
jsc7002 wrote: does anyone know the p/n for the rear upper iso?
52088707AA According to my kj parts catalog |
|
| Author: | jsc7002 [ Wed May 28, 2008 12:26 am ] |
| Post subject: | |
awesome, thank-you! |
|
| Author: | AaronCherokee [ Fri Aug 01, 2008 8:43 am ] |
| Post subject: | |
I am installing the rustys as well. How many conduit nuts do you have to use to get 1/2"? Edit: Nevermind, found it in the first post. Too early.
|
|
| Author: | Tokyojoe [ Tue Aug 05, 2008 11:13 am ] |
| Post subject: | |
Aaron, How'd it go? |
|
| Author: | shaggyislandboy [ Mon Oct 13, 2008 9:57 pm ] |
| Post subject: | |
racnee wrote: jsc7002 wrote: does anyone know the p/n for the rear upper iso? 52088707AA According to my kj parts catalog Does anyone know if this would be the same part number for the rear upper iso for the CRD version of our KJ's? |
|
| Author: | tommudd [ Mon Oct 13, 2008 10:25 pm ] |
| Post subject: | |
shaggyislandboy wrote: racnee wrote: jsc7002 wrote: does anyone know the p/n for the rear upper iso? 52088707AA According to my kj parts catalog Does anyone know if this would be the same part number for the rear upper iso for the CRD version of our KJ's? same ones, only the spring rates are different |
|
| Author: | shaggyislandboy [ Mon Oct 13, 2008 10:32 pm ] |
| Post subject: | |
tommudd wrote: same ones, only the spring rates are different
Thanks Tom. I think I shall be placing an order for a couple.
|
|
| Author: | Burton12 [ Fri Dec 04, 2009 10:31 am ] |
| Post subject: | |
How about a Complete tool list For Installing the Rustys lift Thanks Mark |
|
| Author: | tommudd [ Fri Dec 04, 2009 12:21 pm ] |
| Post subject: | |
same tools are needed for any lift, common hand tools will work, a variety from 10 mm on up but please get better than a Rustys lift
|
|
| Author: | Georg [ Sat Oct 22, 2011 2:42 am ] |
| Post subject: | Re: Installation of Rusty's coil lift + clevis/spring isolat |
Hi guys. In sg's first post I cannot see most pictures (I imagine step-by-step instructions). I can only see 2 photos of the KJ climbing down a rock. Any clues? |
|
| Author: | surfRenegade [ Wed Feb 15, 2012 3:19 pm ] |
| Post subject: | Re: Installation of Rusty's coil lift + clevis/spring isolat |
I know this is a really old post, but can you please fix the pictures? I plan on adding to my OME suspension and I remember these picture being very helpful. Thanks Sam |
|
| Page 2 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|