| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| How To Retrieve Engine Codes without a Scanner... http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=16&t=1714 |
Page 1 of 2 |
| Author: | Katmandu [ Thu Sep 08, 2005 6:42 pm ] |
| Post subject: | How To Retrieve Engine Codes without a Scanner... |
If you want trouble codes follow this procedure: 1. Cycle the ignition key On - Off - On - Off - On within 5 seconds. 2. The odometer will show the P-code for the corresponding Diagnostic Trouble Code number. 3. If no DTC's are present, the cluster will display either: A. "P1684" and "done" B. Or, only "done" P1684 does not indicate a problem; it's only a status, which indicates that the PCM memory has been cleared within the last 50 ignition cycles. "Done" indicates that no DTC's are present and the procedure is complete. To decipher your Code simply Click the Link below... http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?t=1707 |
|
| Author: | GUTomek [ Sun Feb 19, 2006 5:46 pm ] |
| Post subject: | |
I just ran into a code not on your list when I forgot to make the electrical connection to the spark plug. Here you can find a more complete list of codes: http://en.wikipedia.org/wiki/Table_of_OBD-II_Codes |
|
| Author: | omniphil [ Thu Apr 06, 2006 2:05 pm ] |
| Post subject: | |
Just to add to this thread. This does not work on 2006 models. You can no longer check your own codes. Chrysler has a new scan tool for 2006 to retreive the codes.. |
|
| Author: | Special Agent [ Mon Jun 12, 2006 9:56 pm ] |
| Post subject: | |
Is this true? You can't check codes on the 2006? |
|
| Author: | omniphil [ Tue Jun 13, 2006 9:01 am ] |
| Post subject: | |
Special Agent wrote: Is this true? You can't check codes on the 2006?
I've owned chrysler vehicles all my life, I'm very familiar with the on-off-on-off-on procuedure, could never get it to work on the 2006, talked with a tech at the dealer and he confirmed that you can no longer get the codes the old way 
|
|
| Author: | nycrd [ Thu Jul 06, 2006 9:29 pm ] |
| Post subject: | |
This worked on my 05 CRD till one of many TSB's were done. Since the flashes this doesn't work. Any one else noticed this? |
|
| Author: | Flying J [ Thu Jul 06, 2006 10:42 pm ] |
| Post subject: | |
My ability to check codes hasn't worked after the reflashes either. Thanks a bunch Chrysler! |
|
| Author: | seferis [ Thu Jul 20, 2006 12:59 pm ] |
| Post subject: | |
MINE WORKS ONLY WHEN THE ENGINE IS COOL. I TRIED MANY TIMES AFTER SWITCED OFF THE ENGINE BUT I COULD'NT MAKE IT. I MADE IT NEXT MORNING BEFORE START UP CRD 2005 RENEGADE 2.8L |
|
| Author: | Endurance [ Wed Oct 04, 2006 6:21 pm ] |
| Post subject: | |
same here, just got all the recent flashes done and cant get the codes anymore. Worked fine before the flashes. |
|
| Author: | swampdonkyy [ Fri Oct 20, 2006 11:01 am ] |
| Post subject: | |
My 06 will show codes the same way my 03 Ram did...... Hold down the Odometer reset button and Turn the key to the On position the Guages will go through a test and will then show any codes stored after a CEL |
|
| Author: | O_Dogg [ Sat Mar 10, 2007 1:37 am ] |
| Post subject: | |
mine works but only with on-acc-on-acc-on |
|
| Author: | EricsKJ [ Wed Mar 21, 2007 10:04 am ] |
| Post subject: | |
My 05 Sport will go through the display diagnostic and then display "5.7", and it will also display an error "P0457" via the on-off-on-off-on routine. I've found the P0457 error (loose gas cap), but I'm wondering if the "5.7" corresponds to the "P0457" code. 
|
|
| Author: | Fulltimer [ Wed Apr 11, 2007 7:38 pm ] |
| Post subject: | |
My 05 Limited worked using the on - off bit. I got a code that isn't on the list! It's PO315. Anyone know what that is? Terry |
|
| Author: | SavageUrge [ Sun May 06, 2007 11:14 am ] |
| Post subject: | |
This isn't working for me  Does the odometer have to be set on miles or trip or...? I tried several times, making sure I cycled them within 5 seconds and it was fully in each position, but I don't get anything. Not even the code that says everything is OK. Maybe I need a code scanner?
|
|
| Author: | 0311_DoC [ Mon Jul 30, 2007 4:55 pm ] |
| Post subject: | |
updates on if this works? |
|
| Author: | KJ Taz [ Mon Nov 05, 2007 11:58 am ] |
| Post subject: | |
Well on my 06 the check engine light has just come on after installing the lift, but the code it is showings is "6.2" Anyone know what that code is for? |
|
| Author: | KJ Taz [ Mon Nov 05, 2007 3:39 pm ] |
| Post subject: | |
Well I found the problem, now I just have to go get the code cleared. |
|
| Author: | 0311_DoC [ Mon Nov 05, 2007 4:05 pm ] |
| Post subject: | |
KJ Taz wrote: Well I found the problem, now I just have to go get the code cleared.
So what was "The Problem" ? |
|
| Author: | KJ Taz [ Mon Nov 05, 2007 4:16 pm ] |
| Post subject: | |
I had acidently disconnected a couple of vacume lines. I also found that on my 06 it tells you on the over head display what the error code is. Mine was check TPM (I think, something like that anyway). Anyway all is well now. |
|
| Author: | ATXKJ [ Mon Nov 05, 2007 5:57 pm ] |
| Post subject: | |
Typically 3 engine cycles - cold to hot and back will clear a CEL after you've corrected the cause. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|