It is currently Sun Oct 25, 2020 7:14 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: 3" RRO Lift with JBA upper A arms - Trying to fit 235/85r16
PostPosted: Wed Sep 23, 2020 12:46 pm 
Offline
LOST Newbie

Joined: Sat Mar 06, 2010 4:06 am
Posts: 48
Location: Santa Rosa, CA
As the title says I've got a 3" RRO lift with OME parts and JBA upper A arms, and I'm wanting to fit some 235/85r16 tires in there... I know I've gotta do some trimming and pinch weld bashing, but is there anything else I should do? And is there a reason why people put that plastic wheel well liner back in instead of using bedliner in it? Seems like you'd gain an extra 1/4"-1/2" by leaving the liner out and painting the wheel well...

_________________
2006 Liberty CRD Limited @125k
GDE Eco tune engine/trans
Samcos
Suncoast TC
Weeks Stage 2
3.7 airbox
5v bosch glow plugs
3" RRO lift/JBA upper A-arms
Steel roof rails/rack
ORDERED...
Toyo Open Country ATII 235/85r16
Black Steel wheels
RRO sliders
ARB lockers
NEXT ON THE LIST...
ARB Front bumper
WAM rear bumper
Skid plates
Beefier brakes


Top
 Profile  
 
 Post subject: Re: 3" RRO Lift with JBA upper A arms - Trying to fit 235/85
PostPosted: Fri Oct 16, 2020 10:35 am 
Offline
LOST Addict

Joined: Thu Oct 20, 2005 5:42 am
Posts: 2052
Location: Fort Collins, CO
I never took the wheel well liners out. I cut next to the pinch weld, beat it flat and painted it, then used a heat gun to melt the liner flap over and seal it. I just think it looks better with the liners in. I had to trim the front of the liners and the bottom lip of the air dam out by the tires, and remove the washer fluid bottle. I installed a small generic one in front of the airbox, that reuses the factory pump and level switch.

_________________
05CRD: GDE Hot ECU & TCM tunes, Provent, Cat filter, Facet lift pump, TransGo kit, Florida TC, Samcos, stainless brake lines, HDS thermostat,
RL super sliders, Frankenlift IIP, Al's Gen 4.5 Arms, 235/85-16 Duratracs, DTT rear, Elocker front, EVIC+TPMS, Turbo timer, McNally pillar gauges, Weeks Stage II kit.


Top
 Profile  
 
 Post subject: Re: 3" RRO Lift with JBA upper A arms - Trying to fit 235/85
PostPosted: Fri Oct 16, 2020 4:08 pm 
Offline
Moderator
Moderator
User avatar

Joined: Sat Aug 24, 2013 11:36 pm
Posts: 5731
Location: Central GA
Just a suggestion,
With a 3" lift, you could fit some 245/75/16's on stock offset wheels and not have to do anything to liners, welds, etc. They will fit with no rubbing issues.
I have a 2.5" lift with 1/2" clevis spacers and I have 245/75/16 AT's on stock wheels and have never had to do anything and have never had any rubbing or scraping issues. :idea: :wink:

Image

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited :JEEPIN:
Ironman Springs/Bilstein/shocks
Yeti StgIV Hot Tune
Sasquatch BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox
GM11 bld. fan/NAPA HDclutch
IronrockArms/wwdieselMount


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 19 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com