LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

TJM front bar & Slider Plate Photos, poser but in action
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=11370		 Page 1 of 1
Author:  OzLtd [ Sat Aug 12, 2006 9:57 pm ]
Post subject:  TJM front bar & Slider Plate Photos, poser but in action
Did a small trip out yesterday with the bar on for the 1st time. Slider plate has been on for a few months & worth its weight in Gold I say.

These 2 products will be on display at SEMA soon. The guys here in OZ have contacts for people with KJ's in the States. I dont have anything to do with that but I sure hope its someone from this board !!
Image
Image
Image
Image
Image

The slider is awesome. I've cased out many times with the full vehicle weight resting on that plate & it wont budge......the criss-cross fold in it makes it uber strong.
Author:  PitViper [ Sat Aug 12, 2006 11:45 pm ]
Post subject: 
Very nice
Author:  lilmatty [ Sun Aug 13, 2006 12:24 am ]
Post subject: 
I'd buy that bumper based on those pictures...
Author:  kickit_in4wheel [ Sun Aug 13, 2006 1:59 am ]
Post subject: 
I like what I see. Time to start saving...
Author:  OzLtd [ Sun Aug 13, 2006 4:25 am ]
Post subject: 
I ran (as always off road) without my front sway bar. Even with those 16x8 rims + offset, the 245/75/16 MTRs didnt rub at all during full tuck.
I was concerned that they would, but the TJM guys based they're design around what I had chopped out of my front bumper & liner ;) how clever !! haha!!

I'm not running a winch so the front & top of the bar still is solid, but if you want to put a winch in later, you simply 'bang' out the laser cut break aways and presto!!

I also like the fact that the top "Bridge" that holds the spotties, is totally removable - If you have heaps of lights on your roof or whatever, and you like that sleek clean look, just unscrew the bridge !!

The design for the 02-04 is yest to be determined, dont get your hopes up just yet people - it may not look like happening for you guys :(


Lastly, here's a link to the TJM website. It shows the 1st product they developed for the KJ, off my car (it made it onto the website !! :) ! Nudge Bar.
http://www.tjm.com.au/Default.aspx?tabid=57
Author:  DarbyWalters [ Sun Aug 13, 2006 8:25 am ]
Post subject: 
That OX Hand winch is something many here might be interested in...at the bottom of the page referred to above. 2500kg (5500lb)...
Author:  dirtykj [ Sun Aug 13, 2006 9:06 am ]
Post subject: 
Tell me more about the front bumper. How thick is the steel? I see that it curves around the sides. Is the steel thinner there, or do you guys use some heavy presses to roll it?
Author:  OzLtd [ Sun Aug 13, 2006 5:11 pm ]
Post subject: 
dirtykj wrote:
Tell me more about the front bumper. How thick is the steel? I see that it curves around the sides. Is the steel thinner there, or do you guys use some heavy presses to roll it?


Not sure off the top of my head, but i'l find out for you today and repost. The channel is one piece & yeah, rolled at the edges. I think its 3mm from memory but dont quote me just yet.
Author:  Tokyojoe [ Sun Aug 13, 2006 5:59 pm ]
Post subject: 
That's an `05-`06 bumper, right?
Author:  Fouros [ Sun Aug 13, 2006 6:40 pm ]
Post subject: 
yes it is


I will be talking to them in a week or 2 about the 01 - 04 KJ bumper thanks to stu's contacts at tjm, the bumper on stu's truck will be displayed at this years SEMA show
Author:  AZScout [ Sun Aug 13, 2006 10:13 pm ]
Post subject: 
More pics plz...closeup of a sideview if possible. Also, did they shorten it like you were wanting them to? Thx for the pics though. It looks really good. What is the price and when are they available?
Author:  kickit_in4wheel [ Sun Aug 13, 2006 11:57 pm ]
Post subject: 
Is there any reason why the 05-06 bumper wouldn't bolt on to an 02-04 Liberty? Obviously there would be no provisions for the stock turn signal indicators and fog lights, but as long as we cut the fender flares in the right spot, I don't see any other problem...
Author:  OzLtd [ Mon Aug 14, 2006 12:22 am ]
Post subject: 
AZScout wrote:
More pics plz...closeup of a sideview if possible. Also, did they shorten it like you were wanting them to? Thx for the pics though. It looks really good. What is the price and when are they available?


Unfortunately they did not. There would have to be a little "re-inventing" with the support/mounting bracketry + the fact we were running out of time.

I might get it tcked in a bit more down the track if nessessary, but its good for the moment. We did some pretty insane steep decents with mounds of dirt at the bottom pushed up by bulldozers (to barracade the entrace/exits) and they were seriously angled - no rubbing. The front IFS skid scraped a bucket load to give you an idea - and that's my custom modded low profiled skid (removed material & gained 60mm of extra clearance).

I'm going to take advantage of that bottom 45deg angle (face of the bullbar) and install some rock lights for night runs + it helps if I have to attach or remove the front swaybar at night (which IS usually done the night before I go wheeling)

I'll get some more profile shots for you all, but what i'll try & do is hook up with some other KJ buddies of mine with ARB bars & take some pics head on, side by side ect for comparo sake.

I love the way the bar looks as it retains so much of the KJ's Face !! The ARB one seems to make all ARB Bar equipped vehicles look the same (just my 2cts!)

Talk later,
Stu
Author:  Fouros [ Mon Aug 14, 2006 1:08 am ]
Post subject: 
kickit_in4wheel wrote:
Is there any reason why the 05-06 bumper wouldn't bolt on to an 02-04 Liberty? Obviously there would be no provisions for the stock turn signal indicators and fog lights, but as long as we cut the fender flares in the right spot, I don't see any other problem...




Once OZltds bar is finalised i will be going in to tjm to see what we can do to fit it to the 02 - 04 kj's we will keep you posted
Author:  EOD-KJ [ Mon Aug 14, 2006 3:45 am ]
Post subject: 
well ... lemme know when and where i can get that slider plate at....looks beefy...hopefully itll be for sale in 4 months when i come home from iraq
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/