| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Rusty's Sliders HELP!! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=20711 |
Page 1 of 1 |
| Author: | NjjeepKJ [ Mon May 14, 2007 9:18 pm ] |
| Post subject: | Rusty's Sliders HELP!! |
ok i order my sliders through rusty's well actually they were a gift to me from my family for my bday got no instructions with them at all, Called rusty's they sent me them, instruction for a wrangler GRRR frustrating ok to the point.... \ i've done some reasearch and it look like i need to remove the plastic rocker sliders on the sides of the jeep... how do i do this???? |
|
| Author: | JeepinMaxx [ Mon May 14, 2007 10:08 pm ] |
| Post subject: | |
I got one of the 1st Rusty's KJ Rock Rails back in 2002 - came with no instructions... Pretty straight foward - hold them up in place and mark the holes on the unibody. As far as the factory plastic (it's been a while...) but if I remember correctly - it pops off from body clips... (I'll check when I get back home Thursday) |
|
| Author: | scoobybri [ Mon May 14, 2007 10:40 pm ] |
| Post subject: | |
You DO NOT have to remove the plastic strips. In fact, DO NOT!!! It will look horrible with them missing (the pinch weld area is not finished in the 05+ Libertys) You just have to make one small trim cut and they fit perfectly. I'll see if I can find the link to the installation instructions. They are on the Rock Lizard site. Here's the rails installed on my 07. Plastics are intact. 
|
|
| Author: | scoobybri [ Mon May 14, 2007 10:42 pm ] |
| Post subject: | |
Found the links... Installation instructions... http://www.rocklizardfabrications.com/instructions.htm 05+ rocker plastic trim instructions... http://www.rocklizardfabrications.com/i ... s_05kj.htm |
|
| Author: | scoobybri [ Mon May 14, 2007 10:43 pm ] |
| Post subject: | |
Oops, my bad. You have Rusty's sliders, not Rock Lizard. I would think the trim instructions would be similar, though. |
|
| Author: | Jeepjeepster [ Mon May 14, 2007 10:51 pm ] |
| Post subject: | |
yea, they should be similar. Got any pics of the stuff that came with the sliders and the sliders? |
|
| Author: | NjjeepKJ [ Mon May 14, 2007 11:57 pm ] |
| Post subject: | |
they are on rustysoffroad.com when i called them they said i had to reove the plastic to make them fit. i tried just holding them up and the mounting plates would sit and inch to low on the frame for it to bolt up right |
|
| Author: | NjjeepKJ [ Mon May 14, 2007 11:59 pm ] |
| Post subject: | |
actual sliders http://rustysoffroad.com/mm5/merchant.m ... de=kj_skid pic of them on a libby http://rustysoffroad.com/mm5/merchant.m ... de=kj_skid |
|
| Author: | chetos [ Tue May 15, 2007 11:00 am ] |
| Post subject: | |
I still dont think you need to take them off. Follow the instructions given by RL. I know you have Rusty's. Get a hammer or a trim puller and pry the tabs loose. Get pliers and the tabs will just twist out. Now take a knife or a dremel and trim where the two pieces meet in the middle so they both sit flat. There is a little 'L' piece that I cut off on one of them, this helps in sitting flat. My sliders fit right on by doing this. The trim is only maybe 1/8 inch and you have quite a bit of pinch seam to work with. I really can't see Rusty's being that much different unless they drilled the holes in the pinch seam mount really low. If they did, just redrill them higher (new holes). |
|
| Author: | steepcreekfreak [ Tue May 15, 2007 11:11 am ] |
| Post subject: | |
scoobybri wrote: You DO NOT have to remove the plastic strips. In fact, DO NOT!!! It will look horrible with them missing (the pinch weld area is not finished in the 05+ Libertys) You just have to make one small trim cut and they fit perfectly. I'll see if I can find the link to the installation instructions. They are on the Rock Lizard site.
Here's the rails installed on my 07. Plastics are intact. Sorry to high jack this thread. Scoobybri, where did you get that spare tire antenna mount?? I have been thinking about somewhere to put my antenna so I can put my cobra back in but I didn't want to drill or magnet mount on the body. |
|
| Author: | NjjeepKJ [ Tue May 15, 2007 3:06 pm ] |
| Post subject: | |
u know if u look at the pic on rusty's websit it looks like they took them off (the plastic) any one else see it? and i also compared that photo to photo of all model year kj's and it seems like its gone. not to metion taking the plastic off may give me just a smidge more ground clearance on the sides.. |
|
| Author: | scoobybri [ Tue May 15, 2007 4:29 pm ] |
| Post subject: | |
Like I said before, the pinch weld area is not pretty on the 05+ KJs and this is why the plastic is there. If you remove the plastic, it looks unfinished, like if you would remove the wheel well flares. All of the pics on the Rusty's site show the rails on a 02-04 Libbys, which have painted sheet metal there. That sheet metal is NOT there on your Liberty. The plastic is there in its place. If they do not fit correctly with the plastic intact, than they are designed incorrectly. If Rock Lizard and All-Js install properly on 05-07 Libbys, why don't Rusty's (that's a rhetorical question, by the way! 
|
|
| Author: | scoobybri [ Tue May 15, 2007 4:39 pm ] |
| Post subject: | |
I just had a thought. Like someone else said, follow the RL instructions that I linked to. There are about 8 round plastic tabs that are between the body and the bottom part of the plastic. They keep the plastic trim away from the body. These need to be removed before installation to allow the plastic to push up against the body. (The bottom "flap" of plastic will be sandwiched between the slider and the body.) They are about 1/2" thick and are probably the reason that the sliders are sitting too low. You need to use a claw hammer to pull them out. (You will need to trim the plastic where it overlaps as well to allow the plastic to lay flat between the slider and the body.) All of this is in the RL instructions for the 05+ Libertys. |
|
| Author: | jcphoto20 [ Tue May 15, 2007 9:07 pm ] |
| Post subject: | |
scoobybri, do those size tires fit without the spacers? or do they rub on the inside in the front? thanks |
|
| Author: | scoobybri [ Tue May 15, 2007 10:29 pm ] |
| Post subject: | |
Here is a picture of the tab that needs to be removed from between the plastic molding and the body. The round end is visible along the bottom of the plastic. Once you remove the tabs, the plastic can press directly up agains the body. 
|
|
| Author: | scoobybri [ Tue May 15, 2007 10:34 pm ] |
| Post subject: | |
jcphoto20 wrote: scoobybri, do those size tires fit without the spacers? or do they rub on the inside in the front?
thanks Spacers were added to gain some stability after installing the lift. There was no rubbing until AFTER I installed the spacers. Pinch weld did not rub, but they did rub on the front. A little trimming fixed the problem. |
|
| Author: | scoobybri [ Tue May 15, 2007 11:13 pm ] |
| Post subject: | |
steepcreekfreak wrote: Sorry to high jack this thread. Scoobybri, where did you get that spare tire antenna mount?? I have been thinking about somewhere to put my antenna so I can put my cobra back in but I didn't want to drill or magnet mount on the body.
You can see the mount here Look towards the bottom of the post. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|