will a JK fuell filler ring; the little chrome or black ring that takes place of the gas door; work on a liberty? If so where would I go to get thte part. All I can find are the doors and not the ring. If someone could help me out that would be very much appreciated.

I think some have tried on here but dont think antone has found any to fit have they, plus CHROME??? No bling needed for a true Jeep
Tom

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

well i rolled out to the bearest stealership today and measured tank openings. From what i found all jeep and most dodge vehicles use the same size and depth opening. So I would think that it would match up pretty easy.

I think Al did this to his KJ, don't recall the parts' make/model. Might of been off a Dodge.

_________________
2002 Jeep KJ Sport 3.7L 4x4

245/75-16 Mastercraft Courser HSX, 16x7 Cragar, 2" OME MD Lift, ARB Bumper
AEM Brute Force Cold Air Intake, Flowmaster Super 44 Muffler

Currently working on: Full service on transmission & bed-lining ARB bumper

viewtopic.php?f=43&t=84650

i dont think it would fit quite flush bc the wrangler has perfectly vertical sides, and the liberty does not.

_________________
-Jon-
02 Jeep Liberty - LOST Trail Tested Edition - sold
09 VW Tiguan 4motion - current

I think Al's hood scoop and filler came of a Mustang didn't they?

_________________
No one knows as much as all of us.

Yup...I think it was a Mustang. I think he had to do a bit of trimming to get it to fit.

_________________
2002 Jeep KJ Sport 3.7L 4x4

245/75-16 Mastercraft Courser HSX, 16x7 Cragar, 2" OME MD Lift, ARB Bumper
AEM Brute Force Cold Air Intake, Flowmaster Super 44 Muffler

Currently working on: Full service on transmission & bed-lining ARB bumper

viewtopic.php?f=43&t=84650

The scoop was from a mustang, the filler door was for a TJ. He said it didn't fit exactly right, a little small and stuck out 1/4 inch. He also warned that if you went that way you better like it cause you had to drill holes in the body to mount it.

Last suggestion was to check out full size Dodge truck filler doors to see if they were the right size, as far as I know know one has found one that fits exactly or without drilling.

I'd like to find a true locking cover with a black anodized finish. There are so many Liberties out there, Not sure why no one has made one yet.

_________________
2005 CRD "Ol' Blue"
Red Ryder carbine-action, two hundred shot range model air rifle with a compass in the stock and this thing which tells time.
My build page- RL Komodo Rear and TJM Front Bumper, armored, lifted, JBA Steel D30, 4.10s and ARB air lockers.

well so far it sounds like it owuld be pretty easy to do the mod just a bit of time with a test fit a dermel and thats about it. I checked the size of a ram opening and its about an inch to big so i dont think im going to go that way because id rather cut on the new ring instead of the panel itself. An im still looking for a place where i can get the stock fuel ring for an 07 jk.

_________________
$$$$
03 Liberty - Borla
2000 Dak Quad Cab - 31 Mich ATs