LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

KC highlites on 05 front bumper
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=3039		 Page 1 of 1
Author:  Strika [ Thu Oct 27, 2005 1:18 pm ]
Post subject:  KC highlites on 05 front bumper
Hi all, I have looked at the search section, could not find this answer. I want to mount KCs to the front bumper of a 05 renegade. It has the factory fog lights already, but looks like there might be enough room inside of these. has anyone had the bumper apart yet? there was one thing on the search about doing this to a 03, are they the same bumpers? Should I just wait and get a safari rack and mount them on top? Thanks.






05 silver renegade, Skyjacker 2.5 lift, wrangler 245/7016 w/ silent armor, all Mopar skids, catchall mats.
Author:  Guest [ Thu Oct 27, 2005 1:47 pm ]
Post subject:  Re: KC highlites on 05 front bumper
Strika wrote:
Hi all, I have looked at the search section, could not find this answer. I want to mount KCs to the front bumper of a 05 renegade. It has the factory fog lights already, but looks like there might be enough room inside of these. has anyone had the bumper apart yet? there was one thing on the search about doing this to a 03, are they the same bumpers? Should I just wait and get a safari rack and mount them on top? Thanks.


The bumpers are different...as for there being enough room between the factory foglights, what size lights are you planning on using? find out, then measure.

personally, i'd just mount them on a universal light rack if losing the fogs is a big deal to you.
Author:  Guyute1210 [ Thu Oct 27, 2005 2:24 pm ]
Post subject: 
There was another person that took a piece of flat iron, and drilled a couple holes in for the factory fogs on the outside of the piece, and attached the off-road lights to the inside of it, then used the factory mounts to mount the new one piece of metal with the old hardware. So he ended up with the factory fogs on the outside in the exact same place as before with the flat iron inbetween the light and the holes in the bumper with the factory bolts down through it...if you have problems with my rambling, i could 'shop something up.
Author:  Strika [ Thu Oct 27, 2005 2:33 pm ]
Post subject: 
Nate, that sounds about right. Have you heard, is that a very stable system?
Author:  Guyute1210 [ Thu Oct 27, 2005 3:19 pm ]
Post subject: 
Strika,

The problem is, that i've only seen pictures of this setup, and only when they initially did it. I dont remember who dunnit, but i would imagine that if the holes were drilled correctly, and the correct bolt (one with a flat head) was used for the center lights, than i would think it would be stable. If i were to do something like this, i would just try it...a piece of flat steel or iron can't be that expensive if needed to be trashed... Just make sure you measure before you cut or drill, and then measure again...
Author:  KJTX [ Thu Oct 27, 2005 3:23 pm ]
Post subject: 
You can get more info here:
http://www.lostjeeps.com/forum/phpBB3/vie ... php?t=2212
Author:  Guyute1210 [ Thu Oct 27, 2005 3:38 pm ]
Post subject: 
KJTX wrote:
You can get more info here:
http://www.lostjeeps.com/forum/phpBB3/vie ... php?t=2212

There it is...thanks KJTX for finding it...i knew i saw it, but couldnt remember where...
Author:  Strika [ Thu Oct 27, 2005 4:14 pm ]
Post subject: 
Guys, thanks. It looks like I will try something along those lines.
I wish there was a pre fab unit out there.
Author:  grywlfbg [ Sun Oct 30, 2005 8:50 pm ]
Post subject:  KC lites on an '05 Limited
Along these lines, any thoughts on how to do this on a Limited? I was thinking I could get a bull bar but I just want the bar. No brush guards over the lights, and the ARB bar is WAY overkill for me. Just want a way to mount lights for driving in the mountains at night. My garage is too low to allow any overhead mount.

Thanks!
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/