need some lift

Hood297 · **Posted:** Sun Sep 07, 2008 7:27 pm

well i need to add about 1/2-1" of lift to the front. I already have CRD coils so I dont need any stiffer springs, and I can't do a clevis lift since the RC lift is a strut spacer. I have tried several time and cant get it done.

So how much lift would i get out of a upper strut plate?

Any other ideas?

where can i find extended front bumpstops?

XC204 · **Posted:** Sun Sep 07, 2008 8:02 pm

2008 KK liberty clevis is 3/8" longer than KJ you would get about 3/4" maybe TOMMUDD would sell you the set he sounds like he won't be using.

modular · **Posted:** Sun Sep 07, 2008 8:13 pm

For the ext. bumpstops try trailquest.com part number 001903200. These are the Teraflex extended bumps.

Hood297 · **Posted:** Sun Sep 07, 2008 8:51 pm

XC204 wrote:

2008 KK liberty clevis is 3/8" longer than KJ you would get about 3/4" maybe TOMMUDD would sell you the set he sounds like he won't be using.

Well my issue with that is it is a pain to try and move the Clevis down enough to get it off, if i could I'd just add the Conduit nuts. with the springs fully extended I cant get it down enough before hitting the lower a-arm.

thanks for the Bump stop link!

XC204 · **Posted:** Sun Sep 07, 2008 9:55 pm

This post has an alternative spacer.
http://www.lostjeeps.com/forum/phpBB3/vie ... highlight=

jeepkj02 · **Posted:** Sun Sep 07, 2008 10:12 pm

XC204 wrote:

2008 KK liberty clevis is 3/8" longer than KJ you would get about 3/4" maybe TOMMUDD would sell you the set he sounds like he won't be using.

Hey Tom, where do you get the KK forks from? How much? I thought they were 1" taller than the KJ, therefore giving you 2" lift??

tommudd · **Posted:** Sun Sep 07, 2008 10:58 pm

jeepkj02 wrote:

XC204 wrote:

2008 KK liberty clevis is 3/8" longer than KJ you would get about 3/4" maybe TOMMUDD would sell you the set he sounds like he won't be using.

Hey Tom, where do you get the KK forks from? How much? I thought they were 1" taller than the KJ, therefore giving you 2" lift??

got mine from ....Jeep! 60 something each, returned them and yes almost one inch taller

tommudd · **Posted:** Sun Sep 07, 2008 11:01 pm

Hood297 wrote:

well i need to add about 1/2-1" of lift to the front. I already have CRD coils so I dont need any stiffer springs, and I can't do a clevis lift since the RC lift is a strut spacer. I have tried several time and cant get it done.

So how much lift would i get out of a upper strut plate?

Any other ideas?

where can i find extended front bumpstops?

top plate will get you 1/2 inch, plates are 1/4 inch thick. Yes with the lift you have I sure would not want to do a clevis on it! about the only choice you have is the top plate :wink:

Hood297 · **Posted:** Sun Sep 07, 2008 11:01 pm

XC204 wrote:

This post has an alternative spacer.
http://www.lostjeeps.com/forum/phpBB3/vie ... highlight=

excellent find! but I have CRD coils and even with the UBJ nut loose i cant find a spring compressor that will fit in between the coils.

XC204 · **Posted:** Mon Sep 08, 2008 1:06 pm

I have a set of KK 2008 clevis' and they are only 3/8" taller from top of clevis to bolt hole center. as compared to 2004 and 2006 sport. the part # is 5215312AA

Hood297 · **Posted:** Mon Sep 08, 2008 9:00 pm

tommudd wrote:

Hood297 wrote:

well i need to add about 1/2-1" of lift to the front. I already have CRD coils so I dont need any stiffer springs, and I can't do a clevis lift since the RC lift is a strut spacer. I have tried several time and cant get it done.

So how much lift would i get out of a upper strut plate?

Any other ideas?

where can i find extended front bumpstops?

top plate will get you 1/2 inch, plates are 1/4 inch thick. Yes with the lift you have I sure would not want to do a clevis on it! about the only choice you have is the top plate :wink:

ok tom, i know you want something to do so where do i find a set of plates?

renegadekj · **Posted:** Mon Sep 08, 2008 11:26 pm

Rusty's sells the plate and i believe they are around $30.00 or something. And yes they will give you about 1/2" of lift. Be prepared you may have to drill out the holes in the plates to make them fit the bolt pattern on the top strut plate.
Here is a link: http://rustysoffroad.com/mm5/merchant.m ... Code=COILS

josh

Hood297 · **Posted:** Mon Sep 08, 2008 11:33 pm

Thank you!

tommudd · **Posted:** Mon Sep 08, 2008 11:43 pm

OR you could make a set if you know someone with a hot wrench or way to cut out a set. I just happen to know someone who may have the plans :wink:

I just made my own, 1/4 inch thick and they fit better than what I have heard Rustys do :shock:

Hood297 · **Posted:** Tue Sep 09, 2008 12:01 am

well now that sounds even better! let me know! Thanks again guys as always

need some lift

Who is online