pm sent....
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| how to tell if its cv or driveshaft. http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=55171 |
Page 1 of 2 |
| Author: | STINGN [ Thu Aug 26, 2010 4:15 pm ] |
| Post subject: | how to tell if its cv or driveshaft. |
ok, i just installed my wheel spacers and i love them. but after driving for 5 minutes, i started to hear (and feel) and popping noise. it was pretty consistent with the speed i was going. and my wheel seems to wobble when i drive now. i went under the jeep and played with the driver side cv and it was not making to much noise but the front driveshaft was making a ton of noise. would the front driveshaft cause wheel wobble and a constant pop like a cv would? |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 4:44 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
It's your intermediate half shaft.... You can also get a remanned CV at Napa for under $80.... Might as well change it too since it's all ready out ( when you change your half shaft ) There was just a thread about the front drive shaft.... Try searching front and drive and shaft... wheel spacers are PPPPPPPFFFFFFFT! Travolta out! |
|
| Author: | STINGN [ Thu Aug 26, 2010 4:59 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
well i just drove it a little and i think it might be my wheel bearing but im not sure. front drive shaft out. So now its down to the CV or wheel bearing...100% sure its coming from driver side and it makes a pop every turn of the wheel. slow or fast. not in reverse tho. and sometimes when my wheel is turned it does not make a sound |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:01 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
Well if it's drivers side.... No half shaft.... scratch that... Put it on jack stands and spin the wheel.... |
|
| Author: | STINGN [ Thu Aug 26, 2010 5:07 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
spun the wheel but i could not get too much noise from it. it was not spinning that easily so im guessing the bearing might be ceasing up |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:09 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
wheel bearing shouldn't POP..... I'd start tearing it apart.... |
|
| Author: | STINGN [ Thu Aug 26, 2010 5:11 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
well what would make a POP on every rotation of the tire? just a singular pop/thud sound. |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:13 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
half shaft..... |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:15 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
it may sound like it's coming from the drivers side but it's probably not |
|
| Author: | STINGN [ Thu Aug 26, 2010 5:20 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
its for sure coming from the driver side. stood next to it when my dad drove it on all 4 corners |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:22 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
pm sent....
|
|
| Author: | STINGN [ Thu Aug 26, 2010 5:25 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
http://www.youtube.com/watch?v=azgvbEE7vcY |
|
| Author: | tommudd [ Thu Aug 26, 2010 5:45 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
You have a real problem  my first guess would intermediate shaft and CV, noise can travel on them did it do it before you installed the spacers ??? |
|
| Author: | JL Rockies [ Thu Aug 26, 2010 5:50 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
I vote loose lugnuts.... there are many now that those spacers are on there. |
|
| Author: | STINGN [ Thu Aug 26, 2010 5:52 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
tommudd wrote: You have a real problem my first guess would intermediate shaft and CV, noise can travel on them did it do it before you installed the spacers ??? made no noise before hand...it happened about 5 min after i installed them |
|
| Author: | STINGN [ Thu Aug 26, 2010 5:53 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
JL Rockies wrote: I vote loose lugnuts.... there are many now that those spacers are on there. i took off the tires (all 4 actually) and tightened them |
|
| Author: | tommudd [ Thu Aug 26, 2010 5:55 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
Then I would take off the front spacers put the tires back on and try it, now its getting interesting if still doing it back to the intermediate shaft |
|
| Author: | 03CDKJ [ Thu Aug 26, 2010 5:57 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
I love this game! 
|
|
| Author: | tommudd [ Thu Aug 26, 2010 5:57 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
03CDKJ wrote: I love this game! Its all for you John |
|
| Author: | STINGN [ Thu Aug 26, 2010 6:00 pm ] |
| Post subject: | Re: how to tell if its cv or driveshaft. |
03CDKJ wrote: I love this game! you know what game i enjoy http://www.youtube.com/watch?v=Ik-RsDGPI5Y |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|