LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Fender Flares
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=56477		 Page 1 of 1
Author:  WarriorMP31B [ Mon Oct 25, 2010 6:24 pm ]
Post subject:  Fender Flares
After an eventful "Dukes of Hazard" moment on my last excursion, I need a new Driver Side Fender Flare! :banghead: I have a 2002 Jeep Liberty Sport... The below link has been the best price I've seen, so can somebody confirm this is the proper part? Also, can somebody direct me (perhaps somebody who's also been unfortunate enough to have gone through this :lol:) as to all the hardware I'll need for reattaching the new flare?

http://www.rockauto.com/catalog/raframe ... 14-1297598

Not sure if these are some of the clips I'll need or not...

http://cgi.ebay.com/ebaymotors/ws/eBayI ... 0126999041

Thanks!
Author:  H0USE34 [ Mon Oct 25, 2010 8:37 pm ]
Post subject:  Re: Fender Flares
As far as hardware to just attach the flare, yes those are the clips needed. You may also need the pins to attach the flare to the wheel well. I knocked my flare off a few months back and only attached the flare to the fender and it is still on there. Just be sure to put the fender flare outside the wheel well. I would also get in contact with the company selling the flare because when I got my new flare it had all the needed clips attached already. I can't remember where I ended up ordering mine from though.
Author:  WarriorMP31B [ Mon Oct 25, 2010 9:11 pm ]
Post subject:  Re: Fender Flares
Thanks for the reply! I appreciate the information. I took a close look and the Fender Flare itself looks fine, but the Inner Fender was blown to heck... Works for me, that's only about $10!

Same page, but instead of "Fender" select "Inner Fender". Same hardware?
Author:  H0USE34 [ Wed Oct 27, 2010 5:57 pm ]
Post subject:  Re: Fender Flares
Yes the inner fender(wheel well). There are different clips to attach the inner to the fender and to the flare. I didn't have to replace the inner fender but I did remove it after the flare got mauled by a tree and it is attached by 2 or 3 clips you just push into the designated spots on the metal fender. There is also about 7 or 8 plastic rivets that attach the flare to the inner fender. I did not reattach this way and haven't had any issues.
Author:  WarriorMP31B [ Wed Oct 27, 2010 6:14 pm ]
Post subject:  Re: Fender Flares
Thanks. I was able to remove the Fender Flare with all the rivets in tact. Now I just need the hardware to put the Inner Fender in to place (and order the Inner Fender of course).
Author:  WarriorMP31B [ Thu Oct 28, 2010 4:48 pm ]
Post subject:  Re: Fender Flares
So does anybody happen to know what type of clips I need to attach the Inner Fender to the Fender? I have all of the clips to attach the Fender Flare to the Inner Fender.
Author:  JeepinJarhead03 [ Thu Oct 28, 2010 4:53 pm ]
Post subject:  Re: Fender Flares
inner fender to fender? like.. liner to fender you mean maybe? pretty sure it's one of those 1 1/2 inch dia plastic serrated push "plugs" basically

if you're talking about fender FLARE to fender itself, the push pin style fender clips are PN# 5157055aa
Author:  WarriorMP31B [ Thu Oct 28, 2010 5:03 pm ]
Post subject:  Re: Fender Flares
Yes, as I said. I need the clips to attach the Inner Fender (Also Referred to as Fender Liner) to the Fender/Vehicle. I have the clips to attach the Fender Flare to the Inner Fender.
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/