LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

I have a dream...Portal Axles and a supercharger!
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=5718		 Page 1 of 1
Author:  Robby_T [ Thu Feb 09, 2006 9:39 pm ]
Post subject:  I have a dream...Portal Axles and a supercharger!
To all those pioneers out there working on SFA conversions that us mere mortals will eventually get a shop to fit on our vehicles.....have you thought about Portal axles? There seem to be two kinds that have been used for conversions of other vehicles in the past...Volvo 303 axles (second hand only..no longer produced) and Unimog axles. As far as I can tell much less stress on drivetrain as final gear reduction in the hub...lots of ground clearance...and very heavy duty. Unimogs I know are pretty indestructable (as used by the 'Hereford Gun and Country Club' aka 'Them' in the Desert!). Please please please think about it..my dream is my KJ on Unimog axles and 37's...with a supercharger on the engine!

A few links to a Landrover 90 portal conversion...impressive I think you'll agree...those are the volvo axles btw

Image

Image

Image

Image
Author:  JJsTJ [ Thu Feb 09, 2006 11:12 pm ]
Post subject: 
$$$$ I Dream of winning the Lotto too. $$$$

My dream involves a $KJ, $Hemi, $Portals and a tall blonde $$$....... :shock: :wink: :twisted:
Author:  Robby_T [ Thu Feb 09, 2006 11:17 pm ]
Post subject: 
It's a brunette in mine :D

Seriously though I would pay for those axles....saw some on sale for $1100 for the pair (used) so not too bad. Like I said it's a dream..... :(
Author:  Ed [ Fri Feb 10, 2006 12:57 am ]
Post subject: 
Pfft! Portals?

A KJ...
Image

...a 5.7 Hemi...
Image

...an Atlas II...
Image


...30" of adjustable suspension...
Image

...44" Super Swampers...
Image

... and 2 1/2 ton Rockwells.
Image
Author:  ManicMechanicJoe [ Fri Feb 10, 2006 7:20 am ]
Post subject: 
i am diggin the portals but it would be sweet to a see a KJ rockin rockwells... Theres a guy not far from me that builds heavy duty axle shafts for those... If you need heavy duty axle shafts in a rockwell-you have a problem and I want to hang out with you!
Author:  Ed [ Fri Feb 10, 2006 9:57 am ]
Post subject: 
Ha ha! Heavy duty shafts in a Rockwell. That's the axle equivalent of a supercharger on a Hemi.

Oh, hang on...
Image

Anyone know where I can get a heavier-duty transfer case than the Atlas II?
Author:  Se7enLC [ Fri Feb 10, 2006 12:35 pm ]
Post subject: 
portal axles are some impressive stuff. There's really no other way to get that much clearance per tire size. Without them, no matter what kind of lift you get, you'll still only be able to get an axle clearance of (Tire Size / 2) - (Diff Size). A portal axle can raise the axle up 8" or so just like that!

That being said, if I were going to be doing a portal axle conversion, it wouldn't be to a KJ. I like driving my KJ on the road, and I don't think there's any way to make one of those portal axles road-friendly. I bet that land rover is pretty nice though! (if you're on a safari or something)

One of the first sites you find when you search for unimog you can see a mog climbing straight up a 30" concrete step. Impressive!
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/