Im about to buy a lift kit (CRD w/ARB bumper w/winch) would like to run 265/70/16. I would like to know if I need to mix match different lifts ect... OME, Frankenlifts, or differnent spacers or isolators. Or should I just buy the Frankenlift or Rocky-road please give me the best way to go I will pay what ever it takes to do it right the first time.

I have exactly what you want. Frankenlifted with 265-70-16's. After the frankenlift it was up about 3-3.5 inches from stock(including the sag from 145,xxx miles of highway). Then when i went to put the 265-70-16's on the stock rims, they fit just fine, just a bit difficult to balance. When they got mounted they rubbed on the upper control arm. So i ordered 1.25 inch spacers and put one on each hub. That brought everything out nice and good but then rubbed on the pinch and the fog light door.

Pound the pinch down flat, and then cut out the fog light door and you should clear perfectly. I have a couple pictures of my CRD as it sits now.

This was before the spacers


and after the spacers.

_________________
06 CRD limited
Frankenlift, JBA 1/4 top plate, 3 clevis rings, 3 stacked iso's
JBA UCA and quick disconnects
Procomp rockkrawlr 16x8 4.25bs with 265-70-65 General Grabber AT2's
Mopar full skid plates, JCR stage 3 Rock Rails
Kenwood HU, 6.5 pioneer marine grade door speakers, JL stealthbox kenwood amp
GDE HOT tune
Soon to come
RL Rock monitor bumper

That is what Im looking for, so where did you get the lift from.

AllJs has the Frankenlift
www.boulderbars.com

_________________
MUDD'S MOTORSPORT'S We do IFS lift installs ,
03 OVERLAND EDITION /Kilby-Skidrow-Mopar-4XGuard skids/ 2.5 inch TOTAL CONTROL JBA coilovers -JBA Arms/MOABS-31 FALKEN WILDPEAK AT3W / 4.10's etc, 04 Kilimanjaro Edition loaded, plus 05 KJ limited

Mikey likes the bull bar from where did you get that? And about what did it cost if you don't mind me asking

_________________
2006 Liberty CRD Limited Deep Beryl Green Metallic Clear coat, Fumoto valve, MH ProVent (removed), GDE Eco tune,
OME 790/948 springs, OME struts, OME N132L shocks, Jeepin by Al A-arms, Hercules Terra Trac AT2 245/75R16
Weeks Stage 1 EGR delete, 5 volt steel glow plugs

I got the premium franken lift, expensive, but i figured its worth it since a buddy was doing it for cheap. As for the bullbar, im really not sure my dad put it on when he got the car 5 years ago. It doesnt have any distinguishing marks or labels on it so im sorry that i cant really help there

_________________
06 CRD limited
Frankenlift, JBA 1/4 top plate, 3 clevis rings, 3 stacked iso's
JBA UCA and quick disconnects
Procomp rockkrawlr 16x8 4.25bs with 265-70-65 General Grabber AT2's
Mopar full skid plates, JCR stage 3 Rock Rails
Kenwood HU, 6.5 pioneer marine grade door speakers, JL stealthbox kenwood amp
GDE HOT tune
Soon to come
RL Rock monitor bumper

well I wil have to do some research on the bull bar. I like it, like the arb bumper too but its too expensive. I am planning the ome lift.

_________________
2006 Liberty CRD Limited Deep Beryl Green Metallic Clear coat, Fumoto valve, MH ProVent (removed), GDE Eco tune,
OME 790/948 springs, OME struts, OME N132L shocks, Jeepin by Al A-arms, Hercules Terra Trac AT2 245/75R16
Weeks Stage 1 EGR delete, 5 volt steel glow plugs