It is currently Mon Sep 29, 2025 8:26 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 6 posts ] 
Author Message
 Post subject: Exact size of front cradle bolts?
PostPosted: Thu May 19, 2011 7:17 pm 
Offline
LOST Newbie

Joined: Mon Nov 29, 2010 4:26 pm
Posts: 9
Location: Denver Co
I want to do a 1" cradle drop & I was woundering if anyone knew what the exact size of the cradle bolts were off hand. I dont really want to pull all the bolts & check them. Are they all the same size or do they differer from front to back or side to side? Thanks for the help.

_________________
2004 Black Renegade 4x4:

52K miles 3.7L
OME Front Struts 927HD Coils
OME Rear Shocks 948HD Coils
JBA UCAs
Trac-Lok
American Expedition Wheels
Firestone A/T 245/75R16


Top
 Profile  
 
 Post subject: Re: Exact size of front cradle bolts?
PostPosted: Thu May 19, 2011 8:05 pm 
Offline
Lifetime Member
Lifetime Member

Joined: Sat Apr 01, 2006 9:38 pm
Posts: 12988
Location: Colorado Springs
There is so much more then just dropping the cradle for a cradle drop.You must drop the t-case/trans crossmember the same amount.Anything more then about 1/2" will cause UCA issues,and actually make it much harder(maybe impossible) to get the alignment into spec.Basically it's more hassle then what you gain.


Oh and the front cradle bolts(2) are M14X2.0X135mm,grade 10.9,the rear cradle bolts(2) are M12X1.75X135mm,grade 10.9.Must be grade 10.9 or higher.Cost a pretty penny also,about $8-$12 each.


Top
 Profile  
 
 Post subject: Re: Exact size of front cradle bolts?
PostPosted: Sat May 21, 2011 11:16 pm 
Offline
LOST Junkie
User avatar

Joined: Wed Nov 12, 2008 12:09 pm
Posts: 886
Location: Dixie, Maryland
Other then to do more lift then you should why drop the cradle? Honestly the most you can do without a drop will be more then enough for most jeepers and if you need more just do a sfa.

Sent from my PG06100 using Tapatalk

_________________
Fran:2002 Jeep Grand Cherokee Limited 4.7 quadra drive. 31in General Grabber AT2, OME HD, bilstein, IRO sway links, addco rear sway. Kolak 3in cat back flowmaster SUV 50, magnaflow 3in cat, airaid JR kit, ram air, P.I.E. aux adapter, surco 45x50, husky liners.http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=65276&p=719908#p719908


Top
 Profile  
 
 Post subject: Re: Exact size of front cradle bolts?
PostPosted: Sun May 22, 2011 11:34 am 
Offline
LOST Junkie
User avatar

Joined: Fri Jan 30, 2009 9:04 am
Posts: 824
Location: Canada
liquidxit2 wrote:
Other then to do more lift then you should why drop the cradle? Honestly the most you can do without a drop will be more then enough for most jeepers and if you need more just do a sfa.

Sent from my PG06100 using Tapatalk


I think He'd rather spend 60$ on bolts and do the work himself rather than 8-10K on a SFA lol


Top
 Profile  
 
 Post subject: Re: Exact size of front cradle bolts?
PostPosted: Sun May 22, 2011 6:20 pm 
Offline
LOST Newbie

Joined: Mon Nov 29, 2010 4:26 pm
Posts: 9
Location: Denver Co
RED_KJ_666 wrote:
I think He'd rather spend 60$ on bolts and do the work himself rather than 8-10K on a SFA lol


Exactly.

liquidxit2 wrote:
Other then to do more lift then you should why drop the cradle? Honestly the most you can do without a drop will be more then enough for most jeepers and if you need more just do a sfa.


Dont get wrong I would love to do SFA but I dont have the funds right now. I have too many projects right this second.

I just want to get a couple more inches so I can fit some bigger tires & actually have a little flex. I would like to try to keep up with my friends 81' toyota truck. He only has 31s, rear auto locker & can make it a ton more places than I can.

tjkj2002 wrote:
Oh and the front cradle bolts(2) are M14X2.0X135mm,grade 10.9,the rear cradle bolts(2) are M12X1.75X135mm,grade 10.9.Must be grade 10.9 or higher.Cost a pretty penny also, about $8-$12 each.


Thanks for the bolt specs. Saved me some time.

_________________
2004 Black Renegade 4x4:

52K miles 3.7L
OME Front Struts 927HD Coils
OME Rear Shocks 948HD Coils
JBA UCAs
Trac-Lok
American Expedition Wheels
Firestone A/T 245/75R16


Top
 Profile  
 
 Post subject: Re: Exact size of front cradle bolts?
PostPosted: Sun May 22, 2011 8:21 pm 
Offline
LOST Junkie
User avatar

Joined: Wed Nov 12, 2008 12:09 pm
Posts: 886
Location: Dixie, Maryland
Fair enough.

Sent from my PG06100 using Tapatalk

_________________
Fran:2002 Jeep Grand Cherokee Limited 4.7 quadra drive. 31in General Grabber AT2, OME HD, bilstein, IRO sway links, addco rear sway. Kolak 3in cat back flowmaster SUV 50, magnaflow 3in cat, airaid JR kit, ram air, P.I.E. aux adapter, surco 45x50, husky liners.http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=65276&p=719908#p719908


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 6 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 31 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
cron
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com