| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| bullbar build! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=3&t=84517 |
Page 1 of 1 |
| Author: | littlekj [ Mon Apr 25, 2016 9:28 pm ] |
| Post subject: | bullbar build! |
so i recently picked up a 06 kj 3.7 for real cheep. i want to do some stuff to it and starting out i want to put a bull bar on it. the problem is i don't want to spend a bunch on a flimsy one. i am a very capable welder and machinist. my only problem is how to mount it...  any pictures on mounting locations/ideas?
|
|
| Author: | andrew.wenmoth [ Mon Apr 25, 2016 9:47 pm ] |
| Post subject: | Re: bullbar build! |
Start with a detours backbone. Thats my summer project, building a bumper around it. Probably a few more mounting points on the sides but the detour is more than capAble with a winch so i figured its a good starting point Sent from my iPhone using Tapatalk |
|
| Author: | littlekj [ Mon Apr 25, 2016 9:52 pm ] |
| Post subject: | Re: bullbar build! |
i want to build it from scratch tho. i'm a cheep a**. |
|
| Author: | toy4everyseason [ Tue Apr 26, 2016 7:18 am ] |
| Post subject: | Re: bullbar build! |
Have you tried pulling up the instructions for mass produced bull bars and copying the mounts? Here is a link for the one I have sitting in my shed. http://4x4.fatbobsgarage.com/mobile/jee ... p1062.aspx |
|
| Author: | littlekj [ Tue Apr 26, 2016 10:35 am ] |
| Post subject: | Re: bullbar build! |
Thanks I will try that |
|
| Author: | littlekj [ Tue Apr 26, 2016 6:29 pm ] |
| Post subject: | Re: bullbar build! |
I don't see how it's mounted there are a few holes but nothing you can get a wrench in. Would post pictures but don't know how....
|
|
| Author: | flash7210 [ Tue Apr 26, 2016 7:35 pm ] |
| Post subject: | Re: bullbar build! |
Check out the fabrication section. Also, this might offer some clues http://detoursusa.com/kjbackbone_install.php |
|
| Author: | WHITE the civilian [ Thu Apr 28, 2016 3:23 am ] |
| Post subject: | Re: bullbar build! |
Use the four holes a long the bottom of the unibody and dremel the, out to accept 1/2" bolts. I did that and cut two more half inch holes on top.  
|
|
| Author: | littlekj [ Thu Apr 28, 2016 4:56 pm ] |
| Post subject: | Re: bullbar build! |
thanks.  have any more pictures of the mounts?
|
|
| Author: | flash7210 [ Thu Apr 28, 2016 6:25 pm ] |
| Post subject: | Re: bullbar build! |
See those two large holes in the steel frame below the grille? Cut them open and enlarge them a bit. 10-12 inches of 2 inch OD square steel tube fits perfectly in there. And there are already bolt holes. So once you figure out how much you need sticking out, drill holes and bolt them in. Those are now your mounts. Build your bumper from there. |
|
| Author: | littlekj [ Thu Apr 28, 2016 8:11 pm ] |
| Post subject: | Re: bullbar build! |
looks like i was referring to one like an arb but was thinking a beefed up western bar. |
|
| Author: | Mountainman [ Thu Apr 28, 2016 11:50 pm ] |
| Post subject: | Re: bullbar build! |
With the bumper skin off, you'll see some slots where you can slip bolts in they go do into the bull bumper. You beef them up by putting a rectangular piece of steel in there with holes in it so it bites a lot more of the flimsy frame than just a bolt heads worth. Sandwich the frame, or at least that's how I saw one bull mounted. |
|
| Author: | toy4everyseason [ Fri Apr 29, 2016 2:29 pm ] |
| Post subject: | Re: bullbar build! |
I have the Westin mounts in the garage somewhere, I'll try to find them & take a picture of them for reference. They attach to the frame using flat bar with bolts welded to them. They slip into preexisting holes in the frame similar to the M bolts they use to attach the OEM tow hooks. |
|
| Author: | littlekj [ Fri May 06, 2016 10:37 pm ] |
| Post subject: | Re: bullbar build! |
well i got it all built  sadly i don't know how to post pictures. 
|
|
| Author: | G.O.A.T. [ Sat May 07, 2016 2:58 am ] |
| Post subject: | Re: bullbar build! |
littlekj wrote: well i got it all built sadly i don't know how to post pictures. This post is useless without pics. I use Tapatalk to post pics. Sent from my SM-N900P using Tapatalk |
|
| Author: | WHITE the civilian [ Tue May 17, 2016 3:56 am ] |
| Post subject: | Re: bullbar build! |
Download photobucket, upload a photo and click on the uploaded picture to get its link then post it here. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|