It is currently Thu Mar 28, 2024 10:09 am

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 1089 posts ]  Go to page Previous  1 ... 13, 14, 15, 16, 17, 18, 19 ... 55  Next
Author Message
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Mon Dec 10, 2018 3:39 pm 
Offline
LOST Member

Joined: Thu Feb 18, 2010 12:12 am
Posts: 228
Location: Alaska
Hey, my post disappeared or didn't make it in at all.

1. I paid $85.00 plus shipping from IDparts but they're going for $70. for a set now so how does $70. plus $10. for shipping sound?


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Mon Dec 10, 2018 3:48 pm 
Offline
LOST Member

Joined: Thu Feb 18, 2010 12:12 am
Posts: 228
Location: Alaska
2. No advantage to 7v over 5v. OEM ceramic plugs ran 7volts so the 7v metal glowplugs were a drop in replacement. Dealers recommended changing from ceramic to 5v metal plugs with a modification to a glowplug control module and/or programming. I've been reading that folks are using the 5v plugs without any other changes or problems.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Mon Dec 10, 2018 4:03 pm 
Offline
LOST Member

Joined: Thu Feb 18, 2010 12:12 am
Posts: 228
Location: Alaska
3. No mods, as explained in answer #2.

4. I live in southcentral Alaska which is warmer than it once was. Normal winter temps run twenties in the daytime and teens at night with occasional dives below zero, -25°F, which can last for weeks. Hasn't done that for a couple winters. I've been reading, here, that the 7v plugs don't work well below freezing and the 5v are good to about 10°. The ceramic plugs worked better overall except for the engine cratering problem.

I've been stalled on my timing-belt-plus-mods project due to medical problems for awhile which is why they've been sitting here uninstalled. Getting back into it slowly now. You've done more to your jeep in the last year that I have in the last 4-5 years.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Mon Dec 10, 2018 5:40 pm 
Offline
LOST Addict
User avatar

Joined: Sat Aug 27, 2016 9:12 pm
Posts: 2505
Location: Oregon Coast Dairy Country. Land of stumps, dumps, and "Liquid Pumps"
CaptainDean wrote:
WWDiesel wrote:
Quote:
After a year I don't automatically remember where each one goes,

If you need help, holler, I can look a mine for a reference and can send pictures if needed. Probably others willing to help as well if needed... :D

I have been installing connectors today and re-routing the harness from where I initially thought it might go. Believe I have the back of the engine connected. Also identified and taped-back the EGR connectors.

I'm going slowly and trying to assure I have everything at the back connected before I install the front parts. Once the front is on I will have a much more difficult time finding things in the back.

I'm sure this connector will reveal it's place as I put the front stuff on. Until then, I have not remembered where this one goes. It is wrapped in the same bundle as the air conditioner clutch connector. (I have it lifted up and hanging from the alternator mount for the picture)

Image

Dean.

That's the connector for the glow plug harness.

Access tip.

Keep the battery, battery tray, and alternator, and air filter, and filter box removed until after you have the rest of the engine, and cooling stack installed. This greatly helps with access to front and sides as necessary. Also, hook up crankshaft position sensor before attaching the exhaust, water pump, and turbo stuff. It's easier that way.

_________________
'06 Lbrty Sprt CRD 150K

Sasquatch
DSS Turbo
CAT-elimntr
Weeks Stg1&2 EGRfix
PV-200
BLING
vent gauges

IDParts
head
cams
rockers
Timing set
ARP studs
eTn1 GX2123 5v GPs

YETI Custom Tune
Flowmaster 8325508
Carter P76611M
GM 12611872
Hayden 2986
GM 15976889
PATC Custom Billet
2010 Ram Hemi Trans
Sonnax 44957
Transgo kit
Cooper 51770


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Mon Dec 10, 2018 11:20 pm 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
:pepper:
Image :pepper:

:banghead:
Image :banghead:

Before I do anything drastic, I have removed the physical EGR system, but not removed the virtual EGR from the computer. Will it cause this?

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 12:51 am 
Offline
LOST Addict
User avatar

Joined: Sat Aug 27, 2016 9:12 pm
Posts: 2505
Location: Oregon Coast Dairy Country. Land of stumps, dumps, and "Liquid Pumps"
No Probably nothing to worry about.

That happened with mine, just getting all the gunk burned out and the extra cleaning and cylinder lube stuff burned out it looks like. I didn't pull down the whole bottom end like you did, so it took about 10 miles of hellish smoking before it burned it all out.

Does it smell like oil, fuel, or coolant?

You have no provent installed, so the temporary extra blowby through the rings will push more oil and fumes through the CCV system, and back to pre-turbo. Some of this will make it's way through the intake and charge-air system for a while.

_________________
'06 Lbrty Sprt CRD 150K

Sasquatch
DSS Turbo
CAT-elimntr
Weeks Stg1&2 EGRfix
PV-200
BLING
vent gauges

IDParts
head
cams
rockers
Timing set
ARP studs
eTn1 GX2123 5v GPs

YETI Custom Tune
Flowmaster 8325508
Carter P76611M
GM 12611872
Hayden 2986
GM 15976889
PATC Custom Billet
2010 Ram Hemi Trans
Sonnax 44957
Transgo kit
Cooper 51770


Last edited by GordnadoCRD on Tue Dec 11, 2018 1:10 am, edited 2 times in total.

Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 12:57 am 
Offline
LOST Addict
User avatar

Joined: Sat Aug 27, 2016 9:12 pm
Posts: 2505
Location: Oregon Coast Dairy Country. Land of stumps, dumps, and "Liquid Pumps"
take it out and drive it around. Let it come up to full operating temperature. Check to make sure the air is fully bled from the cooling system. It will probably clean it's self out, and the rings will probably take some time to fully seat, since you have all new ones? at least some new ones. Make sure to do some full throttle runs to help them seat, but not so long that any overheat if there are tight spots. I'm sure none of this is completely new to you. Get used to every sound so you know if and when something changes.

_________________
'06 Lbrty Sprt CRD 150K

Sasquatch
DSS Turbo
CAT-elimntr
Weeks Stg1&2 EGRfix
PV-200
BLING
vent gauges

IDParts
head
cams
rockers
Timing set
ARP studs
eTn1 GX2123 5v GPs

YETI Custom Tune
Flowmaster 8325508
Carter P76611M
GM 12611872
Hayden 2986
GM 15976889
PATC Custom Billet
2010 Ram Hemi Trans
Sonnax 44957
Transgo kit
Cooper 51770


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 1:36 am 
Offline
LOST Junkie

Joined: Sat Oct 13, 2018 10:09 pm
Posts: 541
Location: Australia
Great to see! :SOMBRERO:
The smoke will clear soon. :JEEPIN:
Main thing is don't have it siting at idle for long periods. Up & down in revs is good. You will have an exhaust system full of oil, so expect a little smoke till it burns out.

Is it running smooth? Having injector connectors swapped will cause smoke & very rough running. :oops:

_________________
Australian KJ CRD 2006


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 2:35 am 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
Thanks for the feedback everyone !! Smoking being normal makes me feel better.

So far the smoke doesn't smell like anything. Not oil, not fuel, which leaves coolant. An Internet search said coolant would smell sweet -- this doesn't smell sweet, just clean exhaust but with tons of white fumes.

A YouTube video of removing the EGR mentioned pulling the MAF sensor from the air cleaner. He says this shuts down the EGR system. Initially I ran it without the boost tubing or air filter installed and it smoked less, but still white.

I'll go drive around someone else's neighborhood and see if the smoke clears some. I know too many people in my own neighborhood.

It does run smoothly so I don't believe I have any injector connectors switched. The temperature gauge indicated dead cold and that connector is not locking. I will have to steal that connector from the 2006 engine.

Tomorrow (Tuesday) I'll be back at work so I may not get to this until the weekend.

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Last edited by CaptainDean on Tue Dec 11, 2018 9:47 am, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 7:08 am 
Offline
LOST Addict
User avatar

Joined: Sat Aug 27, 2016 9:12 pm
Posts: 2505
Location: Oregon Coast Dairy Country. Land of stumps, dumps, and "Liquid Pumps"
Sounds like it's just a combination of humidity-condensation and CCV stuff.
I thought you said you left the EGR off as in uninstalled. Did I misunderstand?
Disconnecting the MAF will prevent normal operation of the EGR, but an EGR still in place can still leak.
IIRC either the MAF or the EGR being disconnected will throw a trouble code and a check engine light, unless you have a tune that ignores them.

_________________
'06 Lbrty Sprt CRD 150K

Sasquatch
DSS Turbo
CAT-elimntr
Weeks Stg1&2 EGRfix
PV-200
BLING
vent gauges

IDParts
head
cams
rockers
Timing set
ARP studs
eTn1 GX2123 5v GPs

YETI Custom Tune
Flowmaster 8325508
Carter P76611M
GM 12611872
Hayden 2986
GM 15976889
PATC Custom Billet
2010 Ram Hemi Trans
Sonnax 44957
Transgo kit
Cooper 51770


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Tue Dec 11, 2018 9:57 am 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
GordnadoCRD wrote:
Sounds like it's just a combination of humidity-condensation and CCV stuff. I thought you said you left the EGR off as in uninstalled. Did I misunderstand? Disconnecting the MAF will prevent normal operation of the EGR, but an EGR still in place can still leak. IIRC either the MAF or the EGR being disconnected will throw a trouble code and a check engine light, unless you have a tune that ignores them.

That's right, I did leave the EGR parts off, plugging the exhaust port, intake port, and coolant port & removed coolant Y hose connector. However, I have not installed a tune to make the computer ignore the EGR software. Apparently, disconnecting the Mass Air Flow (MAF) sensor from the air cleaner will also make the computer halt operation of the EGR software.

I'll do that and see if the smoke lessens.

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 1:09 am 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
Picked up some diesel fuel additives. Do you guys think any of these are better than the others?

My needs are to remove moisture, and have a normal additive in the fuel.

Image

Rislone claims a "fuel stabilizer and water remover"
Power Services claims "protects against fuel filter icing"
Sea Foam claims "control moisture in fuels"

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 2:52 am 
Offline
LOST Addict
User avatar

Joined: Sat Aug 27, 2016 9:12 pm
Posts: 2505
Location: Oregon Coast Dairy Country. Land of stumps, dumps, and "Liquid Pumps"
AS far as I know, they are all good products, and are pretty comparable.

I use Power Service as that's what's added by local fuel distributors, and if I fill away from home, it will be comparable. White bottle is more for winterizing / anti-gelling, while Diesel Kleen (silver bottle) is more for warmer temps, keeping injectors clean and lubed, and injection pump lubed, and water dissipated all year.

There are other formulas for severely cold (arctic) operating temps, and 911 red bottle for fuel that's already gelling or gelled. If you go to any OTR truck stop, (any one I've been to lately) Power Service MASSIVELY outsells anything else.

SeaFoam is effective stuff in all of their products with a great reputation which is hard to earn and maintain. I know a LOT of people that use it and swear by it.

Rislone, Line of products such as Ring Seal, high mileage (motor honey) Compression Boost, Bars Leaks, etc, must be able to produce enough results against their claims to avoid false advertising claims. They've always, in my experience, been in the "if it sounds too good to be true, it probably is" realm of operation, but I doubt it would be harmful at least. It's most likely comparable to Marvelous Mysterious Mineral Spirits with Red Dye Additive, as they list most of the same "benefits".

Honestly I don't think any of them will hurt at any reasonable concentration/dilution ratios, even others such as Lucas, Stanadyne, or Liqui-Moly, but as you can probably tell, I would not rely too heavily on the Rislone.

EDIT - Sorry about all the edits. It's late. I'm tired. :dead:

_________________
'06 Lbrty Sprt CRD 150K

Sasquatch
DSS Turbo
CAT-elimntr
Weeks Stg1&2 EGRfix
PV-200
BLING
vent gauges

IDParts
head
cams
rockers
Timing set
ARP studs
eTn1 GX2123 5v GPs

YETI Custom Tune
Flowmaster 8325508
Carter P76611M
GM 12611872
Hayden 2986
GM 15976889
PATC Custom Billet
2010 Ram Hemi Trans
Sonnax 44957
Transgo kit
Cooper 51770


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 3:21 am 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
Thanks GordnadoCRD.

Your rundown on each of these products and more is thoroughly appreciated.

I'll use the Power Service up first, then use up the others. Afterward I'll continue to use Power Service.

Don't worry about the number of edits. I edit my posts too, even when I'm not tired.

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 8:04 am 
Offline
LOST Junkie

Joined: Sat Oct 13, 2018 10:09 pm
Posts: 541
Location: Australia
I would normally view additives as snake oil but your case is special as your fuel has been sitting in the tank for over a year.
Sea Foam is great for killing the dreaded black bugs. If you had it, your filter would be blocked by now.
I think you need to empty the tank as best you can & put a Jerry can of fresh fuel in to start with, or you may wish to initially run a line from a Jerry can to the filter & try running on fresh fuel from it. Dont need to worry about the return line.
Have you found much moisture in the filter?

_________________
Australian KJ CRD 2006


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 11:39 am 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
layback40,

Apparently I had just filled the tank last year when the big bang happened. I pumped 9 gallons out through a new filter and still have a half tank.

No water in the filter. This condition lets me think it really was sucking air and water through the click-together connections.

Seems like a good idea to check the water trap daily until a couple tanks have run through.

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Fri Dec 14, 2018 12:44 pm 
Offline
Moderator
Moderator
User avatar

Joined: Sat Aug 24, 2013 11:36 pm
Posts: 7157
Location: Central GA
CaptainDean wrote:
layback40,
Apparently I had just filled the tank last year when the big bang happened. I pumped 9 gallons out through a new filter and still have a half tank.
No water in the filter. This condition lets me think it really was sucking air and water through the click-together connections.
Seems like a good idea to check the water trap daily until a couple tanks have run through.
Dean.

Another very good reason for installing an in-tank fuel pump since it puts everything under pressure and will prevent any ingestion of air or water through the fittings per your description...
:)

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited :JEEPIN:
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount

98 Dodge Cummins 24 Valve


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Sat Dec 15, 2018 5:51 pm 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
Finally finished.

Put some Power Service additive in the tank and drove it around a couple blocks, and down the road a mile. It ran good and sounded good. Temperature came up to normal and the radio still works.

Checked all the vital fluids and added a half gallon of coolant, and a half quart of transmission fluid. I imagine the air bubbles have been chased out of the engine and transmission, but I will check these again after the next short run.

Dean.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Sat Dec 15, 2018 5:54 pm 
Offline
LOST Junkie
User avatar

Joined: Thu Oct 05, 2017 2:22 am
Posts: 693
THANK YOU !!!

TO EVERYONE THAT GAVE ME A GREAT DEAL OF HELP AND SUPPORT. EVEN TO THE PEOPLE THAT CHIMED IN TO ADD COLOR TO THE COMMENTARY.

THANK YOU VERY MUCH !! YOU ARE ALL SUPREMELY APPRECIATED !!

DEAN.

_________________
2005 Jeep Liberty 2.8L CRD 248
Kona, Hawaii (Big Island) USA

Changed Turbo.
100,000-mile service.
Replaced harmonic balancer.
Noise in front axle or 3rd member - removed loose chain in transfer case.
Rebuilt engine - replaced #3 cylinder, piston, valves, head repair. Removed EGR.
Sheared bolts on TC. Replaced flex plate, TC, bolts.


Top
 Profile  
 
 Post subject: Re: Hard to find noise -- clinking and clanking
PostPosted: Sat Dec 15, 2018 6:29 pm 
Offline
LOST Junkie

Joined: Sat Oct 13, 2018 10:09 pm
Posts: 541
Location: Australia
I guess we can assume the smoke has all but gone.

_________________
Australian KJ CRD 2006


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 1089 posts ]  Go to page Previous  1 ... 13, 14, 15, 16, 17, 18, 19 ... 55  Next

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 14 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com