LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

How can I install this antenna?
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=45&t=13123		 Page 1 of 1
Author:  SS-Virus [ Wed Oct 04, 2006 9:25 pm ]
Post subject:  How can I install this antenna?
I just got the antenna, but I don't know how & where to install it. I found a good examble here:
Image
But I don't know how I can install in that area, and what tools I should get.

Thanks
Author:  pixeldzn [ Wed Oct 04, 2006 9:42 pm ]
Post subject: 
You just need a pieve of aluminum angle iron, installed like an upside down L on the top bolts of the spare tire carrier. Then run the coax under the door or under the glass. Done.
Author:  SS-Virus [ Sat Oct 07, 2006 8:15 am ]
Post subject: 
If you have it installed in your vehicle, can you please let me see that Aluminum piece, and if you know the size, and dimension.


Thanks
Author:  Skyjump136 [ Sat Oct 07, 2006 9:06 am ]
Post subject: 
You can purchase that same mount here...

http://www.arizonarockyroad.com/index.html

I think they're only $20 or so. Or just take a look at it and you can probably fashion something similar after a trip to the hardware store. :D
Author:  NomadKJ [ Sat Oct 07, 2006 9:29 am ]
Post subject:  Re: How can I install this antenna?
SS-Virus wrote:
I just got the antenna, but I don't know how & where to install it. I found a good examble here:
Image
But I don't know how I can install in that area, and what tools I should get.

Thanks


Read this article before your install; http://www.firestik.com/Meas-SWR.htm#In ... %20PRO-259
Author:  Signcutter21 [ Sat Oct 07, 2006 11:05 am ]
Post subject: 
Also try searching the Electronic Section for ideas. Tons there. I set mine up similar to the pic you posted, used an antenna mount made for truck mirrors. Just drilled out the holes a bit more to fit over the lug and ran the cable under the door (not the window) and into the weather channels. Hope that helps.
Mike
Author:  warblade666 [ Sat Oct 07, 2006 7:47 pm ]
Post subject: 
I just made one for our KJ last month, sorry no pics right now , but I can get some later.
Author:  W3CSX [ Sat Oct 07, 2006 10:24 pm ]
Post subject: 
I made this for mine. It’s a piece of 1.5" aluminum angle iron cut down to fit around the window opening.

Image

Image

The problem I have seen with most of the mounts like you have in the first pic. Do not allow the glass to open with out removing the antenna. You will have to space it out several inches from the tailgate to clear.

Look at page four of my CarDomain site. I have many more photos of my radio install.

Jason
Author:  SS-Virus [ Sun Oct 08, 2006 7:13 am ]
Post subject: 
W3CSX:
Thats a great installation, really the problem with others is the rear glass gate, I'll show you the installation in my weekend (Thursday & Friday). 8)
Author:  raceinfan [ Sun Oct 08, 2006 8:18 am ]
Post subject: 
W3CSX wrote:
I made this for mine. It’s a piece of 1.5" aluminum angle iron cut down to fit around the window opening.

Image

Image

The problem I have seen with most of the mounts like you have in the first pic. Do not allow the glass to open with out removing the antenna. You will have to space it out several inches from the tailgate to clear.

Look at page four of my CarDomain site. I have many more photos of my radio install.

Jason


Jason nice work, now if you go with the other type setup all you have to do is buy a spring for the botom of the antenna thats what I did works like a charm just pull back & you can open the glass
Author:  Endurance [ Sun Oct 08, 2006 11:20 am ]
Post subject: 
Hey W3CSX, did you get the red Turbo Diesel badge? I was thinking about that but didnt know how it would look like. Do you have a close up shot of that handy?
Author:  4wdParakeet [ Sun Oct 08, 2006 12:07 pm ]
Post subject: 
I used steel angle iron for that bracket. I had to notch the downside of the angle iron so the peice would fit flush with the mount. Careful about how long you go though so you don't have sharp metal corner pushing into the spare tire. It was really easy to make took me an hour or so with hand tools. It works great. If you do put the antenna there you will need a spring on the bottom of the antenna so you can flex it back when you need to open the gate.


Parakeet
Author:  W3CSX [ Mon Oct 09, 2006 7:07 pm ]
Post subject: 
Endurance wrote:
Hey W3CSX, did you get the red Turbo Diesel badge? I was thinking about that but didnt know how it would look like. Do you have a close up shot of that handy?


I ordered it form my local dealer. I believe it was used on the 03-04 (:?:) Dodge Cummins. Sorry I do not have the Part #.
Author:  W3CSX [ Mon Oct 09, 2006 7:17 pm ]
Post subject: 
Sorry I forgot the photo.

Image

So enough of the hijacking. How is the antenna mount coming?

Jason
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/