It is currently Thu Jul 27, 2017 12:42 pm

All times are UTC - 5 hours [ DST ]




Post new topic Reply to topic  [ 11 posts ] 
Author Message
 Post subject: P0101 help
PostPosted: Sun Jul 09, 2017 11:50 am 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
I've been watching the mass air flow over the last couple of weeks and now recently had a P0101 code for not enough air at the mass air flow sensor. The reading that I'm getting at me idle with the engine hot is 10 g/s (I believe the number for health rockers is 15g/s?).

I did go through the diagnostic procedure in the FSM and checked out the boost hoses and didn't see anything wrong with them (I'll be replacing hopefully soon anyway) but they seem to hold pressure fine as boost pressure tops out around 20psi (I do have a low boost issue to that I'm checking out).

After looking at the hoses I cleaned of the MAF sensor and checked the circuit. The MAF sensor was dirty but cleaning did not fix the issue. One thing that I found was at the MAF sensor connector, I should have 2 readings of 5v. With the ignition on I only have 1. Pin 6 has no voltage. I did oh out this specific wire also and have good continuity.

I didn't find a real good explanation of how the sensor works. Should there always be 2 5v signals applied to the sensor? What are your guy's thoughts here?
Image

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sun Jul 09, 2017 2:08 pm 
Offline
LOST Junkie

Joined: Sun May 01, 2011 2:27 pm
Posts: 748
Location: Milford, IL
Was the 10g/s reading when the engine was hot?

_________________
2005 Crd Silver Limited- arps, rockers, 7v etechno's, egr deleted, v6 airbox, metal cac's. Yeti's stage 4 tune. Euro TC, Ram tcm, pml transmission pan, facet lift pump


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sun Jul 09, 2017 2:18 pm 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
Yes, engine was hot.

I do have a stock thermostat currently and actually seems to run a bit cool. Coolant temperature usually averages around 165°F.

I had first looked at the MAF reading a few weeks ago and was getting 15.1 g/s.

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Fri Jul 14, 2017 5:52 pm 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
Still trying to figure this out.

I still have the stock EGR intact (I have the delete kit and will be removing in near future). If that's got enough soot caked in there can that be the cause for the code?

Also, can a P0299 be related to this?

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sat Jul 15, 2017 6:49 am 
Offline
LOST Addict

Joined: Sun Jun 07, 2009 5:10 pm
Posts: 1072
You must let it idle for a minute before measuring the MAF. EGR is on for 60 seconds at idle, then it shuts off. Once egr is off, then the MAF reading has good value to determine rocker arm health.

_________________
Providers of wholly developed aftermarket solutions for the KJ CRD.
(248) 977 - 9531


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sat Jul 15, 2017 9:40 am 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
Alright, I'll check that. I've been checking it as soon as I park.

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sat Jul 15, 2017 3:26 pm 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
I checked this morning after leaving it idle for a bit and did get up to 17.1 g/s. Thanks for that bit of info.

But now that takes me back to my original question. Is something up with the voltage readings I got or do I have something else going on?

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Sun Jul 16, 2017 6:45 pm 
Offline
LOST Addict

Joined: Sun Jun 07, 2009 5:10 pm
Posts: 1072
A new engine will be about 18.3 g/s MAF at idle with egr off. Yours is drifted enough on the flow to flag the P0101 code.

_________________
Providers of wholly developed aftermarket solutions for the KJ CRD.
(248) 977 - 9531


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Mon Jul 17, 2017 8:04 am 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
Is there any fix (besides new rockers)? Does tuning eliminate the code?

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Mon Jul 17, 2017 5:53 pm 
Offline
LOST Member

Joined: Tue Dec 13, 2011 3:08 pm
Posts: 267
Location: Raleigh, NC
May seem like a strange question....but have you checked your air filter? I had a P0101 code thrown a while back and changing the air filter solved it for me. Currently...my MAF readings are about 16.8 G/PS and I am not having issues currently with the P0101 code. Your MAF readings are a bit better than mine so I would think if yours was due to your MAF reading I'd be getting the P0101 as well.

Hope this helps...

Jim

_________________
Stock 06 CRD Limited
Timing belt replaced at 110,000 miles


Top
 Profile  
 
 Post subject: Re: P0101 help
PostPosted: Mon Jul 17, 2017 8:45 pm 
Offline
LOST Member

Joined: Sat Jul 13, 2013 10:18 pm
Posts: 162
Location: Harshaw, WI
Air filter is a few weeks old. Changed it after I noticed the code. Codes have been cleared few times since as well.

Sent from my HTC6525LVW using Tapatalk

_________________
2005 Jeep Liberty CRD
-currently stock, bit working towards updates.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 11 posts ] 

All times are UTC - 5 hours [ DST ]


Who is online

Users browsing this forum: JohnnyCRDhead, mass-hole, Neal and 20 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group. Color scheme by ColorizeIt!
Logo by pixeldecals.com