| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Lift pump wiring http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=40726 |
Page 1 of 1 |
| Author: | crackercrd [ Fri Feb 27, 2009 3:07 pm ] |
| Post subject: | Lift pump wiring |
Well, I the best trade in I could get was $8,200 so I decided to keep it and start the mods. I finally ordered the Cummins lift pump but not the wire harness. Making my own harness is the plan. I looked in to ordering the pins and sockets needed for the pump and they want a minimum order of $50.00!! So my question is: Does any one have any extra pins and sockets for the fuel pump wiring? I would pay for them obviously....I just don't need 50 bucks worth. (I hope  )
|
|
| Author: | widowmaker [ Fri Feb 27, 2009 7:24 pm ] |
| Post subject: | |
I might can help. I just finished installing the pump a few weeks ago....and Love It. I have an 05CRD and just added 2 new wires into my existing wire harness. (ground and pump power) I purchased a new 05 gasser harness and and stripped the 2 wires that I needed. I can pull a couple more wires out and mail them if that will work for you. Just say the word and PM me your address. No charge |
|
| Author: | crackercrd [ Fri Feb 27, 2009 10:30 pm ] |
| Post subject: | |
Thank you sir, very neighborly of you. sending pm now |
|
| Author: | Joe Romas [ Sat Feb 28, 2009 7:59 am ] |
| Post subject: | |
You don't need sockets, just 3 pins and wire 
|
|
| Author: | widowmaker [ Sat Feb 28, 2009 8:38 am ] |
| Post subject: | |
If this is what you are looking for...I can send. By the way, these will be 6 inches too short...so you will have to splice in wire, as I did. I haven't received your PM yet, So just let me know if this works. 
You will just have to cut off one end and put a circular thingamagiggy on the other end for grounding to the vehicle. Like this  [size=18]
|
|
| Author: | TDI4BY [ Sat Feb 28, 2009 8:47 pm ] |
| Post subject: | |
Man, I should have just asked. I need some wires too. I already have the pump. If someone else has the wires let me know 
|
|
| Author: | MTB_TDI [ Sun Mar 01, 2009 12:20 am ] |
| Post subject: | |
The wires you use for the pump are 18 ga. The wires that are left over after the install are 20 ga or smaller. You will need to solder on the ends of the wires that someone sends you. Don't splice the existing wires, you have too much resistance and your pump won't get the power it is supposed to have. I got some wires from someone here and cut of the ends and soldered in 18 ga wires. Mine has worked great!!! |
|
| Author: | crackercrd [ Thu Mar 05, 2009 8:56 am ] |
| Post subject: | |
Thanks Dennis, I got the wires yesterday. I am planning on soldering the ends on to thicker wire and I will let you all know how it goes. thanks again Dennis for the wires!!!! |
|
| Author: | widowmaker [ Thu Mar 05, 2009 5:05 pm ] |
| Post subject: | |
My pleasure bro. I hope your installation goes as smooth as mine did. |
|
| Author: | crackercrd [ Mon Mar 23, 2009 5:16 am ] |
| Post subject: | |
Install went great, runs like a top. I just wanted to thank everyone that did all the leg work and research, I would have never attempted this mod without all the confidence inspiring write-ups! YOU GUYS ROCK! |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|