Hello Fellas,

Quick question:

Which of the hard lines on the right (passenger) side of the transmission is the return line from the cooler?

Top or bottom?

TIA.

_________________
06 CRD LIMITED- Factory Belly Armor, Hooks.
EHM, MagnaFlow SS Cat Back, FS-2500, HDS 001 TStat, Some Gauges, PML Trans Pan, PML Diff Cover, Marinco Mod, FIA Blanket, Cooper Discoverer ATR 225/75, CTS 245/70, Front-JBA 2.25" C/Os, Rear-OME HD, JBA UCA, SS Brake Lines.

Upper is to, lower is from

_________________
'05 CRD Limited
Pricol EGT, Boost
GDE Hot '11; EDGE Trail switched
SEGR; Provent; Magnaflow;
Suncoast T\C, Transgo Tow'n'Go switch;
Cummins LP module, Fleetguard filter, Filterminder
2.5" Daystar f, OME r; Ranchos; K80767's, Al's lifted uppers
Rubicons, 2.55 Goodyears
Four in a row really makes it go

Well its the one from the driver's side of the bottom of the cooler-- not sure if one can see this with the stock valances/air dams in place-- one way to tell is on a cold start-- run the engine for ```5 mins and shut down and "feel " the lines coming out of stock cooler and return line will be noticeably cooler by touch.

_________________
2006 CRD LTD 2.8L VM Motori turbo,CAC, 100K-new timing belt
ORM-SEGR, Trans cooler, CLIII hitch front/rear, Journey HD controller
Mopar skids,"Stone Soup" rails, KK clevis fork 1" mild lift w/Daystar stops
215x85 LRD BFG Commercial A/T's, Rola Rack, V6 airbox, Fumoto valve
10K winch, B5 Biodiesel (ULSD CP3 lube)
Its a Diesel baby!

Thanks. Going to install the temp sensor on Monday.
Just want to make dang sure before I cut the line.

Silverdiesel- I will trace it from the bottom of the cooler from the drivers side and will also do the feel test.

gmctd-I'm assuming "lower is from" means from the cooler and is the return to the tranny.

Just making sure.

PS- What the best tranny pan sealer/RTV you have found to use on our vehicle?

TIA.

_________________
06 CRD LIMITED- Factory Belly Armor, Hooks.
EHM, MagnaFlow SS Cat Back, FS-2500, HDS 001 TStat, Some Gauges, PML Trans Pan, PML Diff Cover, Marinco Mod, FIA Blanket, Cooper Discoverer ATR 225/75, CTS 245/70, Front-JBA 2.25" C/Os, Rear-OME HD, JBA UCA, SS Brake Lines.

Use the black stuff from Jeep. It will hold the pan in place without bolts. Add bolts for extra assurance.

_________________
2006 Black Jeep Liberty CRD Limited
K&N, Samco Hoses, Michelin 245/70-16 LTX A/T2, Fumoto F-102, V-Force Muffler, Mopar, Hitch, Trailer Wiring, Skid Plates, Slush Mats, Rear Shelf, Predator Stage 1, Transgo, ORM & CodeReader, Facet 40109 Pump
"IT'S A DIESEL THING, YOU WOULDN'T UNDERSTAND"
Certified Services Auto & Truck Repair

Clean the pan and trans rails with lacquer thinner, then Permatex Black RTV - lower is from cooler

_________________
'05 CRD Limited
Pricol EGT, Boost
GDE Hot '11; EDGE Trail switched
SEGR; Provent; Magnaflow;
Suncoast T\C, Transgo Tow'n'Go switch;
Cummins LP module, Fleetguard filter, Filterminder
2.5" Daystar f, OME r; Ranchos; K80767's, Al's lifted uppers
Rubicons, 2.55 Goodyears
Four in a row really makes it go

Thanks, fellas.

_________________
06 CRD LIMITED- Factory Belly Armor, Hooks.
EHM, MagnaFlow SS Cat Back, FS-2500, HDS 001 TStat, Some Gauges, PML Trans Pan, PML Diff Cover, Marinco Mod, FIA Blanket, Cooper Discoverer ATR 225/75, CTS 245/70, Front-JBA 2.25" C/Os, Rear-OME HD, JBA UCA, SS Brake Lines.