i cant find any information about the cp3 inj. pump on the CRD. iv tried google and so on. Is is a bosch pump like the cummins? if you have any info please post. I also have an account with Mitchell OD and i still cant find any info other than replacement directions and so on. I know a fair share about the CP3 on a CRD Cummins but not the liberty. thanks guys

_________________
06 Cummins 2wd- industrial injection sliver bullet 66,pdi manifold,smarty(tnt tune),Dr. Performance predator w/ race tune,Fass 150/200,Goerend full billet trans,Pusher intake manifold,snow meth,boost fooler,cal tracs, Stage 2 AFE, about 9 isspros, II dual feed lines, wicked injection pump, mag hytec's, studs,spings and cam.

2005 CRD

yes, bosch CP3. can't tell you much else about it though.

_________________
http://www.Colorado4Wheel.com
"Its not about what you can DO with your Jeep, its about where you can GO with your Jeep."
Knowledgeable - But Caustic

The CP3 on the CRD has a gear pump on the rear side to suck the fuel from the tank and the one on the Cummins does not and requires a lift pump

_________________
Atlantic Blue 06 CRD Limited (his)
Joined by a 2000 XJ Classic (hers)

I think the better question, is what information are you looking for?

Just because it is a CP3 doesn't really mean anything. There are many different types, designs, flow capacity, pressure rating, internal design, that all fall under the designation CP3.

For the most part, the CP3 is being phased out slowly, being replaced by other CP-series pumps that are more flexible and capable than the CP3.

hey guys,

yes i know there are many cp3's. i was wanting a part number to the CRD cp3. thats it. im not going to debate that its diff. than the cummins.

_________________
06 Cummins 2wd- industrial injection sliver bullet 66,pdi manifold,smarty(tnt tune),Dr. Performance predator w/ race tune,Fass 150/200,Goerend full billet trans,Pusher intake manifold,snow meth,boost fooler,cal tracs, Stage 2 AFE, about 9 isspros, II dual feed lines, wicked injection pump, mag hytec's, studs,spings and cam.

2005 CRD

right, thats why i have a 200gph pump on my cummins.

_________________
06 Cummins 2wd- industrial injection sliver bullet 66,pdi manifold,smarty(tnt tune),Dr. Performance predator w/ race tune,Fass 150/200,Goerend full billet trans,Pusher intake manifold,snow meth,boost fooler,cal tracs, Stage 2 AFE, about 9 isspros, II dual feed lines, wicked injection pump, mag hytec's, studs,spings and cam.

2005 CRD

do you know if there is a number on CP3 itself that you're looking for?

would phots help?

I one sitting in my garage.

-dkenny

_________________
84 BB school bus, DD8.2L turbo ->the transmission died..too expensive to fix..it'll be heading to the scrap yard..4/11)..Bus gone to Scarp 8/23/11
06 Liberty CRD
'99 dodge ram 2500 quad cab, 4x4, 24v
all Biodiesel powered when its warm enough

Kenny,

im around the raleigh area.....you mind if i send you a pm? i would like to look at the pump or something and take some measurements of some stuff....or you could psot some pics. thanks!

brent

_________________
06 Cummins 2wd- industrial injection sliver bullet 66,pdi manifold,smarty(tnt tune),Dr. Performance predator w/ race tune,Fass 150/200,Goerend full billet trans,Pusher intake manifold,snow meth,boost fooler,cal tracs, Stage 2 AFE, about 9 isspros, II dual feed lines, wicked injection pump, mag hytec's, studs,spings and cam.

2005 CRD

not at all.pm away..

I sent you one..

-dkenny

_________________
84 BB school bus, DD8.2L turbo ->the transmission died..too expensive to fix..it'll be heading to the scrap yard..4/11)..Bus gone to Scarp 8/23/11
06 Liberty CRD
'99 dodge ram 2500 quad cab, 4x4, 24v
all Biodiesel powered when its warm enough