LOST JEEPS :: View topic - 4 new engines available

These engines are hood ornaments without a wire harness, pinout and an ECM. The cheetah engine pictured is completely different than the VM engine used in the US KJ CRD. It was a ground up redesign and does not even share the same block. However, in stock form this engine can push 200 hp and would do wonders in a Wrangler if it could be made to run.

Author:	camo [ Thu Mar 08, 2012 11:16 pm ]
Post subject:	4 new engines available
here is the ebay link for those in need of an engine. http://www.ebay.com/itm/TURBO-DIESEL-EN ... es&vxp=mtr

Author:	GreenDieselEngineering [ Thu Mar 08, 2012 11:31 pm ]
Post subject:	Re: 4 new engines available
These engines are hood ornaments without a wire harness, pinout and an ECM. The cheetah engine pictured is completely different than the VM engine used in the US KJ CRD. It was a ground up redesign and does not even share the same block. However, in stock form this engine can push 200 hp and would do wonders in a Wrangler if it could be made to run.

Author:	ACRucrazy [ Thu Mar 08, 2012 11:31 pm ]
Post subject:	Re: 4 new engines available
Wrong 2.8 however. That is the new one for the FWD.

Author:	maxwellp [ Thu Mar 08, 2012 11:44 pm ]
Post subject:	Re: 4 new engines available
There is also one based on the VM that may go in to a Chevy pick up. It was in Diesel magazine. Most likely will not see it in the US.

Author:	TJ2 [ Fri Mar 09, 2012 12:30 am ]
Post subject:	Re: 4 new engines available
97 GreenDieselEngineering wrote: These engines are hood ornaments without a wire harness, pinout and an ECM. The cheetah engine pictured is completely different than the VM engine used in the US KJ CRD. It was a ground up redesign and does not even share the same block. However, in stock form this engine can push 200 hp and would do wonders in a Wrangler if it could be made to run. I ran into a guy in Grand Jct, CO a few years back who had bought a diesel engine on German ebay when Daimler owned Chrysler. He paid $1500 USD and claimed it bolted right into his TJ. It looked like an excellent fit. I wonder if those were test engines? Anybody with a Wrangler would LOVE that set up. . . . or just about any small diesel for that matter. If my '97 TJ had one it would NEVER have gotten sold.

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

4 new engines available http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=65710	Page 1 of 1

Author:	ATXKJ [ Sat Mar 10, 2012 8:51 pm ]
Post subject:	Re: 4 new engines available
Quote: wire harness, pinout and an ECM wonder if the Euro LOST folks could help?????

Author:	MrMopar64 [ Sat Mar 10, 2012 11:22 pm ]
Post subject:	Re: 4 new engines available
Those engines can't be bolted to anything but the 62TE since the rear face of block is different from RWD engines. The ECU for that engine is designed to communicate with something 2007 or newer, to try and put it into something older (KJ, TJ, etc) makes it more valuable as a boat anchor.

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/