| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Front CV shaft play (YouTube) too much? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=72275 |
Page 1 of 1 |
| Author: | painemann [ Sat Oct 27, 2012 7:21 am ] |
| Post subject: | Front CV shaft play (YouTube) too much? |
I am hearing some noise out of the front that only really is audable When the jeep is warm and over 35mph. Could this be the cause? http://www.youtube.com/watch?v=3zXT_xO0mb0&sns=em |
|
| Author: | papaindigo [ Sat Oct 27, 2012 8:40 am ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
I have no clue how much play is too much but I have experience CV issues on a different vehicle and would note that the noise (clicking or whatever) tends to be worse on turns and the bad joint is the one in the direction of the turn. If you do replace be careful of what you get as lots of folks have been sold a replacement that's noticeably too short but like 1" or so. IIRC NAPA rebuilds are ok and I think there are DIY rebuild kits out there for just the joint. |
|
| Author: | nursecosmo [ Sat Oct 27, 2012 10:19 pm ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
I've had this going on for the past 6 months or so and it's getting worse. There is no clunking or clicking when cornering but there is a sort of rattle/thumping which usually occurs at light throttle or when I let off the throttle. Thinking about getting a couple new half shafts from O'reiles. |
|
| Author: | tjkj2002 [ Sat Oct 27, 2012 10:28 pm ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
Don't buy "new" CV axles unless there from the dealership.That can't read the specs correctly in china and they always end up being to short and cause issues. Buy only remaned CV axles,at least they will be the correct length. |
|
| Author: | papaindigo [ Sun Oct 28, 2012 7:21 am ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
nursecosmo for that rattle/thump sound you might consider motor mounts not CV axles. |
|
| Author: | painemann [ Sun Oct 28, 2012 8:59 am ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
nursecosmo wrote: I've had this going on for the past 6 months or so and it's getting worse. There is no clunking or clicking when cornering but there is a sort of rattle/thumping which usually occurs at light throttle or when I let off the throttle. Thinking about getting a couple new half shafts from O'reiles. I have a similar issue but its hard to descibe the sound. The sound I am hearing sounds a lot like a bad bearing or more so like a very (its not , all new brakes about a month ago)corroded rotor that is scraping the caliper bracket. As I said its difficult to describe. |
|
| Author: | nursecosmo [ Sun Oct 28, 2012 9:23 am ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
papaindigo wrote: nursecosmo for that rattle/thump sound you might consider motor mounts not CV axles. Thanks papa, I did consider motor mounts but the the bumping does not corolate with rpm, only with vehicle speeds from 30 to 70 Mph and does not occur with a loaded engine. I'll certainly take another look though. |
|
| Author: | warp2diesel [ Sun Oct 28, 2012 7:56 pm ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
When I watched you video, I saw the front dif wiggle too, not just the CV, check to see if there is something else loose. |
|
| Author: | painemann [ Mon Oct 29, 2012 6:12 am ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
warp2diesel wrote: When I watched you video, I saw the front diff wiggle too, not just the CV, check to see if there is something else loose. thanks warp, I was going to ask about that also ha! I noticed that the diff mount might be worn, it has a little play in it but the inner shaft play is what I am more concerned about. Is it excessive? I will definitely not buy the Chinese new parts, its rebuild or reman for me. |
|
| Author: | ibedonc [ Mon Oct 29, 2012 3:29 pm ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
do not forget to look at the front drive line , that will ring like a bell if it is going mine is currently off until I can get a reman one |
|
| Author: | Big Montana [ Mon Oct 29, 2012 7:43 pm ] |
| Post subject: | Re: Front CV shaft play (YouTube) too much? |
painemann wrote: nursecosmo wrote: I've had this going on for the past 6 months or so and it's getting worse. There is no clunking or clicking when cornering but there is a sort of rattle/thumping which usually occurs at light throttle or when I let off the throttle. Thinking about getting a couple new half shafts from O'reiles. I have a similar issue but its hard to descibe the sound. The sound I am hearing sounds a lot like a bad bearing or more so like a very (its not , all new brakes about a month ago)corroded rotor that is scraping the caliper bracket. As I said its difficult to describe. Dude! I think I have the same issue. I had a front bearing replaced in the front because that's what i thought the noise was. It's still there. I better try a different shop and see if it's the front shafts. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|