| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Jeep won't start http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=73920 |
Page 1 of 1 |
| Author: | cadman [ Sun Jan 27, 2013 2:49 pm ] |
| Post subject: | Jeep won't start |
Hi all I'm new to this forum. I have a 2.8 crd 2002 auto. About 6 weeks ago i started to have problems starting it so checked glow plugs and all were fine then I thought it might be fuel so I put on a new filter and electric pump still no better it has also cut out 3 time once on outside lane overtaking a bus(near s--t myself). I managed to get it going and get it home now it won't start at all so put a new map sensor and cam position sensor still no joy. Done the ignition trick got codes p0340.So changed cam sensor don't know what these ones are. P1655. P1511. P1130. Now thinking crank sensor but would appreciate any feed back |
|
| Author: | racertracer [ Sun Jan 27, 2013 8:00 pm ] |
| Post subject: | Re: Jeep won't start |
cadman wrote: p0340. P1655. P1511. P1130. P0340 - Camshaft Position Sensor Circuit Malfunction P1655 - Trouble code P1655 means: EVAP Purge Solenoid Control Circuit ????????????????? P1511 - This code will set when: TP less than 3.7% or TP greater than 9.8% Vehicle Speed zero mph Engine Speed less than 250 rpm ECT is between 5°C (41°F) and 100°C (212°F) IAT greater than 5°C (41°F) Battery Voltage greater than 10 volts Pedal Position less than 15% DTC P1511 is a (type A) DTC P1130 - HO2S Circuit Low Variance Bank 1 Sensor 1 I think you need the dealer to scan it and read the codes with the Starscan tool..... Or try another scanner with the latest updates. |
|
| Author: | kjjet [ Sun Jan 27, 2013 8:16 pm ] |
| Post subject: | Re: Jeep won't start |
You still may have a fuel problem? Air in the system before the fuel pump? 1. Do you have a 2nd gen fuel filter head? The old one lets air in. 2. You could place a 4 inch piece of clear hose between the fuel head and fuel pump. after priming there should be no air in the line. Good luck |
|
| Author: | ChooChooman74 [ Sun Jan 27, 2013 8:54 pm ] |
| Post subject: | Re: Jeep won't start |
He says 2002 with a 2.8. Didnt the 02 exports come with a 2.5 and racor fuel heads? Sent from my DROID BIONIC using Tapatalk 2 |
|
| Author: | kjjet [ Sun Jan 27, 2013 10:12 pm ] |
| Post subject: | Re: Jeep won't start |
ChooChooman74 wrote: He says 2002 with a 2.8. Didnt the 02 exports come with a 2.5 and racor fuel heads? Sent from my DROID BIONIC using Tapatalk 2 Your correct. Still look for air? |
|
| Author: | Billwill [ Mon Jan 28, 2013 3:26 am ] |
| Post subject: | Re: Jeep won't start |
P1130 is fuel rail pressure malfunction small leak detected! You sure you get P1655 and not P1685? P1655 does not make sense! Re-check there is no air in the fuel system! You can download the 2002 Service manuals here. Download the 2002 Jeep KJ Service Manual and you must download the 2.5_2.8 Export Diesel supplement for your Export Diesel which will be a 2.5 CRD if it is the 2002 model...2.8 Export CRD came out in about 2004 I believe.  http://www.colorado4wheel.com/manuals/Jeep/KJ |
|
| Author: | cadman [ Mon Jan 28, 2013 6:29 pm ] |
| Post subject: | Re: Jeep won't start |
It was code 1652 sorry and it's a 2003 2.8 doing my head in. |
|
| Author: | racertracer [ Mon Jan 28, 2013 8:56 pm ] |
| Post subject: | Re: Jeep won't start |
•P1652 Powertrain Induced Chassis Pitch Output Circuit ????? What ever that means? |
|
| Author: | Billwill [ Tue Jan 29, 2013 3:19 am ] |
| Post subject: | Re: Jeep won't start |
cadman wrote: It was code 1652 sorry and it's a 2003 2.8 doing my head in. Then download the 2003 Service manual from the link I posted although I would suggest you first download the 2.5_2.8 Export Diesel supplement as that covers the Export engines and has the error codes.  I would chase the P1130 code first! |
|
| Author: | cadman [ Wed Jan 30, 2013 5:49 am ] |
| Post subject: | Re: Jeep won't start |
Thanks for that will post my findings when done |
|
| Author: | cadman [ Tue Feb 05, 2013 2:27 pm ] |
| Post subject: | Re: Jeep won't start |
ok now ive replaced the crankshaft position sensor got jeep started and ran ok came back and wouldnt start primed it up and it started but plunger never goes solid so i clamped the hose to the high preasure pump and it went solid iscrewed it down and left it overnight and was still solid in the morning will it be the fuel line from filter to pump (cant see any visual leaks) or is there seals in the pump or anywhere else |
|
| Author: | cadman [ Wed Feb 06, 2013 2:05 pm ] |
| Post subject: | Re: Jeep won't start |
Replaced all the rubber fuel lines and it seems to have cured the problem. Thank god. Thanks for all the help also done the elephant hose and bypassed theft and it is far more responsive |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|