| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Torque Pro/OBDII/ELM327 problems http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=75026 |
Page 1 of 2 |
| Author: | JieselDeep [ Wed Apr 24, 2013 2:51 pm ] |
| Post subject: | Torque Pro/OBDII/ELM327 problems |
My system...Smart phone with Torque Pro and Bluetooth ELM327 reader will only work for about 20 miles/30 minutes and then the sensors seem to stop updating. Is anyone else having this issue? Anything I can do to fix it? Thanks, Jon |
|
| Author: | ChooChooman74 [ Wed Apr 24, 2013 4:45 pm ] |
| Post subject: | |
Typical on the 06 Sent from my Nexus 7 using Tapatalk HD |
|
| Author: | striperman36 [ Wed Apr 24, 2013 4:53 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
half of my sensors don't work at all like the MAF! |
|
| Author: | ChooChooman74 [ Wed Apr 24, 2013 9:02 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
striperman36 wrote: half of my sensors don't work at all like the MAF! Are you using the right protocol? Sent from my DROID BIONIC using Tapatalk 2 |
|
| Author: | JieselDeep [ Wed Apr 24, 2013 9:24 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
I'm using ISO 9141-2 (5B Init, 10.4K Baud) I trIed disabling the ELM327 auto timing adjust, but It didn't seem to help. |
|
| Author: | CATCRD [ Wed Apr 24, 2013 10:47 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
groelzj wrote: My system...Smart phone with Torque Pro and Bluetooth ELM327 reader will only work for about 20 miles/30 minutes and then the sensors seem to stop updating. Is anyone else having this issue? Anything I can do to fix it? Thanks, Jon My 2005 does it too. Exactly what adapter do you have? Got a link to it? |
|
| Author: | striperman36 [ Thu Apr 25, 2013 9:10 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
ChooChooman74 wrote: striperman36 wrote: half of my sensors don't work at all like the MAF! Are you using the right protocol? Sent from my DROID BIONIC using Tapatalk 2 As far as I can tell. |
|
| Author: | Auberon [ Sun Apr 28, 2013 3:04 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Is it worth slowing the refresh rate? |
|
| Author: | DOC4444 [ Sun Apr 28, 2013 5:56 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
With engine warm, what do you see for a boost value at idle? I get -17. Someone once suggested an adjustment. I tried changing the minimum value to zero, but it did not work. DOC |
|
| Author: | JieselDeep [ Tue Apr 30, 2013 3:37 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Sorry, I'm delayed in my response... Don't know the OBDII adapter. No longer available on Ebay. Mine is Opaque blue and is about the second smallest size I have found on ebay. Slowing the refresh rate doesn't seem to make a difference. I get -17 for boost at idle too, and correction doesn't work for me either! I'm game for trying another OBDII reader...I can always give this one to my Fiancee. I just got her an android phone, so she could make use of it! Anyone have one that works with the 2005 without crapping out after a few minutes? (Got a link?) Thanks, Jon |
|
| Author: | DOC4444 [ Tue Apr 30, 2013 6:22 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
On this one, it is the 5th one down from the top: http://www.ebay.com/sch/i.html?_trksid= ... &_from=R40 Blue and orange graphics Hope whoever had the fix for negative boost readings notices this........... DOC |
|
| Author: | striperman36 [ Tue Apr 30, 2013 9:35 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Once I changed the protocol iso 9141-2 everything was fine |
|
| Author: | DOC4444 [ Tue Apr 30, 2013 10:06 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Did that fix the boost value problem as well? |
|
| Author: | striperman36 [ Tue Apr 30, 2013 11:02 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
yes doc it did. my maf # is 19 a 50' above sea level |
|
| Author: | DOC4444 [ Tue Apr 30, 2013 11:40 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
How do you change the protocol? (I can't seem to find it....) Thanks! DOC |
|
| Author: | JieselDeep [ Tue Apr 30, 2013 11:42 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Doc, I think it was in the vehicle profile section when you first launch the app. HTH, Jon |
|
| Author: | striperman36 [ Tue Apr 30, 2013 3:02 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
groelzj wrote: Doc, I think it was in the vehicle profile section when you first launch the app. HTH, Jon that is correct Jon and Doc |
|
| Author: | flash7210 [ Wed May 01, 2013 3:48 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
I have never used torque pro. I noticed it is not available for iPhone. Is it a free app for android? Anybody know if there is a version that will work on a laptop running Linux? |
|
| Author: | JieselDeep [ Wed May 01, 2013 5:38 pm ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Torque pro is a paid app for android $5 I think). Apple products (even macbooks) won't 'talk' to the bluetooth chip in an obdii reader because Apple is so restrictive of their hardware and software that it would take $$$,$$$ to get a device approved with the OS. There are some linux OBDII programs out there. Try: http://batman.homelinux.com/blog/blueto ... omment-246 for a start. There should be something there that would lead you in the right direction! |
|
| Author: | flash7210 [ Sun Jun 09, 2013 9:27 am ] |
| Post subject: | Re: Torque Pro/OBDII/ELM327 problems |
Is there a way to adjust the temperature reading? I have a 195 deg thermostat but 188 is the highest reading I have seen. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|