| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| New engine installed, one hiccup remains P1202 http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=76999 |
Page 1 of 1 |
| Author: | 81Willis [ Wed Oct 09, 2013 6:18 pm ] |
| Post subject: | New engine installed, one hiccup remains P1202 |
I recently replaced the engine in a 2006 Liberty due to a valve head dropping into cyl #4. The engine was a low mileage (27000) unit coming from a wrecker in florida. The engine came complete with fuel pump, turbo, injectors, rail, and all fuel system components attached to the engine. I put a new timing belt on it before installing it just to be safe. After all was said and done I have one lingering issue. After a cold night outside, the engine starts fine but gives a CEL, with code P1202 Fuel System Overpressure, which puts the engine into a limp mode with little to no boost. If the engine is warm, restarting it will result in no CEL, restored power, which lasts the rest of the day until another night outside. I have the entire fuel rail from the old engine with the pressure control unit and the sensor still attached, also the entire high pressure fuel pump from the old engine, and 3 of the fuel injectors. Any suggestions on what to do to diagnose this problem? Luckily shotgunning parts at it doesn't cost money for parts, but I am limited on access to this vehicle, it belongs to a friend who paid me to do the swap for him. |
|
| Author: | Hexus [ Wed Oct 09, 2013 7:02 pm ] |
| Post subject: | Re: New engine installed, one hiccup remains P1202 |
1st or 2nd gen fuel head? Try the other sensor, might even try the rail. Is the ECU you're using coded for those 4 injectors? Did you flash it with the new information? That may be why it's throwing over pressure codes. |
|
| Author: | CATCRD [ Wed Oct 09, 2013 10:17 pm ] |
| Post subject: | Re: New engine installed, one hiccup remains P1202 |
Do you have an Android device? You can get the torque app and a Bluetooth obd reader and read the value of rail pressure from the ecu. Maybe see if it's acting funny. |
|
| Author: | MrMopar64 [ Wed Oct 09, 2013 11:01 pm ] |
| Post subject: | Re: New engine installed, one hiccup remains P1202 |
The codings of the injectors won't have any bearing on the overpressure setting. Either the MPROP on the pump is stuck open, or the PCV is jammed shut. I would make sure that you dont have the cyl 4 injector and the PCV connector swapped since they are the same. Otherwise, i would swap the MPROP from your old running engine to this one and see if the issue clears up. |
|
| Author: | 81Willis [ Thu Oct 10, 2013 1:30 pm ] |
| Post subject: | Re: New engine installed, one hiccup remains P1202 |
It is a second gen fuel filter head, I changed that with the engine. I'm fairly certain that injector 4 plug is correct, otherwise we would have power problems all the time. I am thinking that if the engine only has 27000 miles on it then it must have been sitting for a long time. I am going to try to run some diesel purge through it to see if it will clear it up. I will report back after this is done. |
|
| Author: | 81Willis [ Fri Oct 11, 2013 8:14 pm ] |
| Post subject: | Re: New engine installed, one hiccup remains P1202 |
After spending the night in a warm garage the jeep started great and ran great all day. I had my friend bring it over and we ran a full can of diesel purge through it. Tonight he is going to park it outside again and we'll see how it works tomorrow morning. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|