Even Chuck Norris is scared of a Libby CRD
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Done! Could not have done it without Geordi and this board!! http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=80976 |
Page 1 of 1 |
| Author: | taroo [ Mon Dec 29, 2014 11:38 pm ] |
| Post subject: | Done! Could not have done it without Geordi and this board!! |
Just completed the followings: New Timing Belt New Water Pump New TB idlers New TB tensioner Installed ARP studs (130/125 ft lbs) New injector crush washers and rubber debris washers Installed WEEKS KIT- Removed EGR, removed EGR Cooler, Removed Flow Control Valve, removed cooler to valve block. Removed water line running from EGR cooler to WP inlet. Plugged both ends. Installed WEEKS KIT. Installed new Alternator dampener Installed new fan clutch Installed new drive belt Drained coolant and went back with new G-05 Zerex at 70% concentration. ------------ Made my own alignment pins for valve cover installation (M-8/1.25 x 2.5") Made radiator drain valve opener from hex wrench cut to length ------------ Geordi was a great help and support. Could not have done this without his board entries and support. Others helped as well through their contributions to the board. ------------- Hardest part-reinstalling the valve cover by myself!! Must use grease on rockers and alignment pins. -------------- Timing is easy - crank set at 90 Degrees ATDC, align fuel pump witness mark to mark on engine, pins were already in E/I cams, install belt, tension so rod is in tensioner window, remove E/I pins, rotate by hand two revs, retension, done. -------------- The turbo is free to breathe now! Lots of power and more peppy. Getting the EGR out physically gives maximum boost to the turbo. ------------- ARP studs give me comfort and hope of never having a leaking or blown head gasket. ------------- Well...lots of work but fun and challenging. Used a combo of the FSM and this board for torque values. You will need a good 50-250 torque wrench for the ARP studs. You will need a smaller torque wrench for all other torquing. |
|
| Author: | Infinite_Karma [ Tue Dec 30, 2014 4:23 am ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
Very impressive! Congratulations taroo. Any pictures of the finished product that you'd like to share? We always love seeing the end results. |
|
| Author: | Diver1430 [ Tue Dec 30, 2014 3:45 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
Could not agree more!!!! Did same stuff, except put on new head gasket after having head and valves cked by machine shop. Also put in new thermostat and cut out the mufffler and cat. A bit disappointed that I did not pick up any MPG. Have 22MPG on both CRD's with GDE tune. A friend has one with 175K and he gets 29-30 and has no tune, nada. No mods, timing belt at 150K because I harrassed him to have it done. Go figure. Marine diesel is at 2.35Gal. down here. That s better than good!!!!! |
|
| Author: | ArmyChief [ Tue Dec 30, 2014 6:45 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
Congrads!..this board and Geordi are good people! |
|
| Author: | thermorex [ Tue Dec 30, 2014 6:59 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
ArmyChief wrote: Congrads!..this board and Geordi are good people! Geordi is not people. He is some sort of chuck Norris of the Crd, lol. |
|
| Author: | ArmyChief [ Tue Dec 30, 2014 7:03 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
Even Chuck Norris is scared of a Libby CRD
|
|
| Author: | taroo [ Tue Dec 30, 2014 8:00 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
ArmyChief wrote: Congrads!..this board and Geordi are good people! So....question. Been running around in the CRD and is more peppy and will check the mileage over time. I believe the Turbo is free to breathe now. I hear it whistling, not whining, not grinding, just whistling and purring on spin up and spin down. I checked with Geordi on this and since there is no grinding, whining, etc then it is just a liberated (no EGR or Flow Control Valve) to interfere. Just the turbo, CAC hoses, and intercooler between it and the intake at the valve cover. So, back to my question...have others with WEEKS Kit and total bypass or removal of the EGR system (EGR, EGR Cooler, FCV, etc) hear their turbo more? I have read the board back to 2008 on the pros/cons of no EGR as it relates to Boost positive pressure, boost negative pressure, and Exhaust Gas Temperature (EGT). As an aside, I am considering the Weeks vent pod with a Glow Shift gauge. So, just looking for the experiences in Turbo whistling sound changes with the installation of the Weeks Kit. |
|
| Author: | flman [ Wed Dec 31, 2014 8:21 am ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
taroo wrote: ArmyChief wrote: Congrads!..this board and Geordi are good people! So....question. Been running around in the CRD and is more peppy and will check the mileage over time. I believe the Turbo is free to breathe now. I hear it whistling, not whining, not grinding, just whistling and purring on spin up and spin down. I checked with Geordi on this and since there is no grinding, whining, etc then it is just a liberated (no EGR or Flow Control Valve) to interfere. Just the turbo, CAC hoses, and intercooler between it and the intake at the valve cover. So, back to my question...have others with WEEKS Kit and total bypass or removal of the EGR system (EGR, EGR Cooler, FCV, etc) hear their turbo more? I have read the board back to 2008 on the pros/cons of no EGR as it relates to Boost positive pressure, boost negative pressure, and Exhaust Gas Temperature (EGT). As an aside, I am considering the Weeks vent pod with a Glow Shift gauge. So, just looking for the experiences in Turbo whistling sound changes with the installation of the Weeks Kit. Mine both seem to have more of a roar to them with out the restrictions in place any more. |
|
| Author: | mecne [ Wed Dec 31, 2014 3:45 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
Adding my Kudos to this thread.. to everyone that posts back on any Help Me!! Thread with there insight and knowledge. I did a bunch of similar work with the addition of Rockers and Head gasket a little over a month ago, and would have been lost without the help of this Forum. Still waiting for the Life Membership to open up again so I can contribute in some way . If I could buy everyone a Beer that helped me along the way I would Happy Holidays to all , and Cheers for a New Year!!! |
|
| Author: | ArmyChief [ Wed Dec 31, 2014 3:51 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
There's a Life Membership? 
|
|
| Author: | mecne [ Wed Dec 31, 2014 4:13 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
ArmyChief wrote: There's a Life Membership? Ya , a bunch of people have the Lifetime Member Tag like flman . I PM'd the Admin and got this back allyrand wrote: Lifetime memberships will be coming back soon. Just hang tight. thanks Want to give back in anyway I can .. 
|
|
| Author: | flman [ Wed Dec 31, 2014 4:26 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
mecne wrote: ArmyChief wrote: There's a Life Membership? Ya , a bunch of people have the Lifetime Member Tag like flman . I PM'd the Admin and got this back allyrand wrote: Lifetime memberships will be coming back soon. Just hang tight. thanks Want to give back in anyway I can .. And I got a cool green tshirt and stickers for the rear of the Libbys. 
|
|
| Author: | ArmyChief [ Wed Dec 31, 2014 4:33 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
I'm jealous..I'm coming to your house and steal sticker
|
|
| Author: | taroo [ Wed Dec 31, 2014 5:53 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
[quote="mecne"]Adding my Kudos to this thread.. to everyone that posts back on any Help Me!! Thread with there insight and knowledge. I did a bunch of similar work with the addition of Rockers and Head gasket a little over a month ago, and would have been lost without the help of this Forum. Still waiting for the Life Membership to open up again so I can contribute in some way . If I could buy everyone a Beer that helped me along the way I would Happy Holidays to all , and Cheers for a New Year!!![/quote Mecne, Read your thread and was feeling for you in your experience. I so thought I was going to have to pull the head as well when I put the intake, belt, etc back on and attempted two manual revolutions to hit a hard stop at 270 degrees! (I also had a puffing sound coming out of a injector luckily to find I had forgotten to torgue it down) My stomach sank and I read your thread. Luckily, I pulled the intake and saw I had knocked a rocker off so used alignment pins and monkey grease (on rockers) and got it on and all was well. Anyway....your thread helped me just so you know. Lots of good heads on this board. Now to find someone with a machine shop to pick up on the t-stat mod that the fellow who moved to Australia started. |
|
| Author: | ArmyChief [ Wed Dec 31, 2014 6:08 pm ] |
| Post subject: | Re: Done! Could not have done it without Geordi and this boa |
There is a new t-stat mod in Canada, Jeff is having them machined..don't have link, but do a search |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|