greiswig wrote:
Dirtmover wins the prize: #4 was bad, after a little over a year.
What's the prize?
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| P1261 and Etecno resistance http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=81168 |
Page 1 of 1 |
| Author: | greiswig [ Thu Jan 22, 2015 3:03 pm ] |
| Post subject: | P1261 and Etecno resistance |
Looks like one of my Etecno plugs has gone south, at least according to the computer. Can someone verify which cylinder 1261 code should belong to? I checked #1 (closest to radiator) and I get a reading of about 3 ohms. |
|
| Author: | gmctd [ Thu Jan 22, 2015 5:18 pm ] |
| Post subject: | Re: P1261 and Etecno resistance |
greiswig wrote: Looks like one of my Etecno plugs has gone south, at least according to the computer. Can someone verify which cylinder 1261 code should belong to? I checked #1 (closest to radiator) and I get a reading of about 3 ohms. If you have not, try disconnecting the 4-wire GP plug in the middle of the harness, measure each GP for reference - plug pinout is in FSM section 8W |
|
| Author: | greiswig [ Thu Jan 22, 2015 8:50 pm ] |
| Post subject: | Re: P1261 and Etecno resistance |
gmctd wrote: greiswig wrote: Looks like one of my Etecno plugs has gone south, at least according to the computer. Can someone verify which cylinder 1261 code should belong to? I checked #1 (closest to radiator) and I get a reading of about 3 ohms. If you have not, try disconnecting the 4-wire GP plug in the middle of the harness, measure each GP for reference - plug pinout is in FSM section 8W Oh, that's right. I forgot there was an intermediate connector. Thanks! |
|
| Author: | dirtmover [ Fri Jan 23, 2015 10:13 am ] |
| Post subject: | Re: P1261 and Etecno resistance |
P1261 is #1 but don't forget that some of the early '05's had the harness back to front so this might actually be #4 in your case. 3 ohms sounds high for a cold plug. I'm not familiar with the Etecno1 plugs but I'd expect them to be in the <1 ohm range. |
|
| Author: | greiswig [ Mon Jan 26, 2015 2:25 pm ] |
| Post subject: | Re: P1261 and Etecno resistance |
Dirtmover wins the prize: #4 was bad, after a little over a year. |
|
| Author: | thermorex [ Mon Jan 26, 2015 2:38 pm ] |
| Post subject: | Re: P1261 and Etecno resistance |
greiswig wrote: Dirtmover wins the prize: #4 was bad, after a little over a year. What's the prize?
|
|
| Author: | greiswig [ Mon Jan 26, 2015 4:40 pm ] |
| Post subject: | Re: P1261 and Etecno resistance |
thermorex wrote: greiswig wrote: Dirtmover wins the prize: #4 was bad, after a little over a year. What's the prize? Well, you didn't win it, so why should you find out? 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|