is this what you're looking for ?
actually I guess this is the front side - just off the engine
image #11
http://www.trucktrend.com/how-to/engine/1403-2005-jeep-liberty-crd-timing-belt-change/
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Pictures of engine side of aluminum rear timing cover http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=83433 |
Page 1 of 1 |
| Author: | 95Z28A4 [ Sat Nov 07, 2015 11:17 am ] |
| Post subject: | Pictures of engine side of aluminum rear timing cover |
I am in the process of fabricating a mechanical fan bracket elimination plate to make room for an electric fan. The plate will be fabricated from 1" thick aluminum using 1.25" aluminum round stock for the two idler pulley spacers. The plate will need an additional spacer on the back side where it bolts through the timing cover to the front of the block. This hole is the bottom most hole of the fan bracket that uses the looong bolt. I am planning to use 2" aluminum round stock for this spacer and tack weld it to the back side of the plate. Does anyone have pictures of the engine side of the aluminum rear timing cover? I want to be sure the 2" round stock won't stress the cover when it is clamped to the engine block with the 2" round stock and the long bolt. I don't think it will, but a picture will help me be sure. Thanks. |
|
| Author: | Mountainman [ Sat Nov 07, 2015 12:21 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
hmm, I'll go check, but I don't think I have the rear cover off of one ATM. But, I probably will in a week when I go at a bad sleeve. I probably have you covered if no one else has one apart |
|
| Author: | flman [ Sat Nov 07, 2015 4:16 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
One of the members here shared this. https://secure.flickr.com/photos/684420 ... 389449367/ |
|
| Author: | jws84_02 [ Sat Nov 07, 2015 4:50 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
Pm me your cell number. I'll send ya a pic. Also, I have that other pulley boxed up but was 5 minutes late getting to the post office today. It will go out monday. |
|
| Author: | 95Z28A4 [ Sat Nov 07, 2015 6:38 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
flman wrote: Good pics, but unfortunately none show the engine side of the rear timing cover. |
|
| Author: | flman [ Sat Nov 07, 2015 6:46 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
95Z28A4 wrote: flman wrote: Good pics, but unfortunately none show the engine side of the rear timing cover. Basically a flat piece of aluminum, with the same outlines of the steel cover. Sorry the pics did not work for you, but good to have for a future reference when you are replacing a part you cant see. |
|
| Author: | ATXKJ [ Sun Nov 08, 2015 4:16 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
is this what you're looking for ? actually I guess this is the front side - just off the engine image #11 http://www.trucktrend.com/how-to/engine/1403-2005-jeep-liberty-crd-timing-belt-change/ |
|
| Author: | 95Z28A4 [ Sun Nov 08, 2015 5:33 pm ] |
| Post subject: | Re: Pictures of engine side of aluminum rear timing cover |
Yep, that's the front side. jws84_02 sent a couple pics of the engine side of the timing cover with measurements. Thanks Josh! I have the information that I need. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|