LOST JEEPS :: View topic - WTB Front Axle mounts

Perhaps I'm dense but what do you mean by "front axle differential mounts"? PN or pictures would be helpful.

I have a set thats just sitting in my shop.....

Sent from my SM-N900P using Tapatalk

I am in Appleton, Wisconsin. Thanks for the help! Shoot me a cost or PM me if you want.

Sent from my SM-G900V using Tapatalk

Heres what I have. Pulled off a low mileage 06 CRD.

Sent from my SM-N900P using Tapatalk

Sorry for posting in this topic, maybe its archived or olb, but i have few questions.
First of all English is not my native language so sorry for any mistakes.

I have bad bushings on exact parts shown on image few posts up.

Can someone tell me exact name of part number so i can find them in my country...
Thank you for help!

Go to Napa and get new. Replace the old ones if you get spare brackets from previous posts. Easy peasy and not worth the work for using old ones. Bushings can't be more than 10-20 a piece.

Author:	choppertime94 [ Mon Nov 16, 2015 11:07 pm ]
Post subject:	WTB Front Axle mounts
Hello to all CRD fans! I have been reading this forum for a few months as it has helped me a ton. However, this is my first post and I need some help. I am looking to buy some front axle differential mounts. I can only find them at the dealer so far at a hefty cost. Does anybody have some they would part with?? I have a 2005 Liberty CRD Limited 4x4 edition. Thanks for your time!

Author:	flash7210 [ Tue Nov 17, 2015 9:15 am ]
Post subject:	Re: WTB Front Axle mounts
Thats not a common part for replacement. I doubt anyone has spares lying around. You may want to get some from a junk yard or ask this question in the KJ 4x4 section and see who replies.

Author:	papaindigo [ Tue Nov 17, 2015 10:16 am ]
Post subject:	Re: WTB Front Axle mounts
Perhaps I'm dense but what do you mean by "front axle differential mounts"? PN or pictures would be helpful.

Author:	mass-hole [ Tue Nov 17, 2015 11:46 am ]
Post subject:	Re: WTB Front Axle mounts
Are they different than what is on the standard KJ though because they slid the diff over towards the passenger wheel?

Author:	JeepMorrison [ Tue Nov 17, 2015 2:16 pm ]
Post subject:	Re: WTB Front Axle mounts
I have a set thats just sitting in my shop..... Sent from my SM-N900P using Tapatalk

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

WTB Front Axle mounts http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=83500	Page 1 of 2

Author:	choppertime94 [ Tue Nov 17, 2015 3:03 pm ]
Post subject:	Re: WTB Front Axle mounts
papaindigo wrote: Perhaps I'm dense but what do you mean by "front axle differential mounts"? PN or pictures would be helpful. I was wondering why mine are blown out at 148k miles too! Anyway here is a picture of the brackets with the rubber isolators inside the mounts. Should be part numbers 52059475AD and 52059472AC.

Author:	Mountainman [ Tue Nov 17, 2015 5:56 pm ]
Post subject:	Re: WTB Front Axle mounts
I think I know of two of us that have them (Illinois and Idaho). Where are you located? Might as well get them with cheap shipping

Author:	choppertime94 [ Tue Nov 17, 2015 6:00 pm ]
Post subject:	Re: WTB Front Axle mounts
I am in Appleton, Wisconsin. Thanks for the help! Shoot me a cost or PM me if you want. Sent from my SM-G900V using Tapatalk

Author:	Mountainman [ Tue Nov 17, 2015 9:49 pm ]
Post subject:	Re: WTB Front Axle mounts
choppertime94 wrote: I am in Appleton, Wisconsin. Thanks for the help! Shoot me a cost or PM me if you want. Sent from my SM-G900V using Tapatalk no problem, you should ask jws84_02 as he's a lot closer and he's parting one out. Let me know if you strike out and I'll dig around to see how good of condition mine are in.

Author:	jws84_02 [ Wed Nov 18, 2015 10:56 am ]
Post subject:	Re: WTB Front Axle mounts
Yep, I have those pieces. But I'm not sure of their condition. I'll check when I get home

Author:	JeepMorrison [ Thu Nov 19, 2015 2:05 am ]
Post subject:	Re: WTB Front Axle mounts
Heres what I have. Pulled off a low mileage 06 CRD. Sent from my SM-N900P using Tapatalk

Author:	choppertime94 [ Thu Nov 19, 2015 9:00 am ]
Post subject:	Re: WTB Front Axle mounts
JeepMorrison wrote: Heres what I have. Pulled off a low mileage 06 CRD. Sent from my SM-N900P using Tapatalk JeepMorrison, how is the condition? Any rips in the rubber?? How much to ship all three to Appleton, Wisconsin if they're in good shape?? PM me if needed. Thanks!

Author:	JeepMorrison [ Thu Nov 19, 2015 2:54 pm ]
Post subject:	Re: WTB Front Axle mounts
Sent ya a pm Sent from my SM-N900P using Tapatalk

Author:	thermorex [ Mon Nov 23, 2015 9:25 pm ]
Post subject:	Re: WTB Front Axle mounts
Go to Napa and get new. Replace the old ones if you get spare brackets from previous posts. Easy peasy and not worth the work for using old ones. Bushings can't be more than 10-20 a piece.

Page 1 of 2	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/

Author:	mindcircus [ Wed Jan 04, 2017 2:05 pm ]
Post subject:	Re: WTB Front Axle mounts
Sorry for posting in this topic, maybe its archived or olb, but i have few questions. First of all English is not my native language so sorry for any mistakes. I have bad bushings on exact parts shown on image few posts up. Can someone tell me exact name of part number so i can find them in my country... Thank you for help!

Author:	WWDiesel [ Wed Jan 04, 2017 3:11 pm ]
Post subject:	Re: WTB Front Axle mounts
mindcircus wrote: Sorry for posting in this topic, maybe its archived or olb, but i have few questions. First of all English is not my native language so sorry for any mistakes. I have bad bushings on exact parts shown on image few posts up. Can someone tell me exact name of part number so i can find them in my country... Thank you for help! Part Numbers are universal! Front Differential mounting Part Numbers for gassers (3.7) are different than diesels. The front cradle on the CRD sets a little bit lower than the gassers do and so does the differential along with it setting a little bit more to the left side of the vehicle than a gasser... The differential is mounted further to the driver’s side on the CRD and the axle shafts on a CRD are different lengths to compensate for this. Therefore, the part numbers are different in this area for gassers as opposed to diesel Jeeps, so do not get them confused! [EK0]=Engines - All 3.7L 6 Cylinder Gas [EN0]=Engines - All 4 Cylinder Turbo Diesel 1. CRADLE, front suspension 52128994AE 1 [EK0] 52129013AE 1 J, U [EN0] 4. BRACKET, Mounting 52059467AD 1 J, U [EK0], Left Rear 52059475AD 1 J, U [EN0], Left Rear 5. BRACKET, Mounting 52059465AD 1 J, U [EK0], Left 52059473AD 1 J, U [EN0], Left 6. BRACKET, Mounting 52059464AD 1 J, U [EK0], Right 52059472AC 1 J, U [EN0], Right

Author:	mindcircus [ Wed Jan 04, 2017 11:00 pm ]
Post subject:	Re: WTB Front Axle mounts
Thank you for your replay! Huh, i cant find any of this parts in my country... Mine is 2.8 CRD 2006. I have issues while i start to go, and in turns. I feel crack/kick noise, but its not CV joint...so my mechanic find some "space" on this spots: There is space left and right, i mean they r moving... But i cant find Bushings for that parts... What you can suggest me?

Author:	mindcircus [ Fri Jan 06, 2017 11:09 pm ]
Post subject:	Re: WTB Front Axle mounts
Still cant find bushings... Only whole parts for 500$... Thats just... Sent from my HUAWEI NXT-L09 using Tapatalk

Author:	crasher [ Tue Jul 11, 2017 5:18 pm ]
Post subject:	Re: WTB Front Axle mounts
thermorex wrote: Go to Napa and get new. Replace the old ones if you get spare brackets from previous posts. Easy peasy and not worth the work for using old ones. Bushings can't be more than 10-20 a piece. I've got a 'clunk' up front while driving down the road, each time the steering passes from left to right through the centerline, and again when passing from right to left through the centerline. I had the JBA upper control arms, springs and shocks replaced last winter, and rechecked all the bolts/fasteners for torque last week. They all checked out, so I'm trying to run through my options. Those two bushings up front move left/right about a half inch when I put a pair of channellocks on 'em and squeeze, so I'm thinking it's a place to start. Are those bushings actually replaceable? I put the bracket number and 'bushing' into the google search for each, and got an answer, but before I get my hopes up - has anyone gotten the bushings and done the replacement into the brackets?