rcdukes wrote:
Anyone change JUST the filter? Will it dump all the oil in the pan?
You can change just the filter without loosing all the oil! Just replace with a new filter and add oil back to the full mark...
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Oil change with Fram PH8A. Oil quantity? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=84282 |
Page 1 of 2 |
| Author: | rcdukes [ Thu Mar 24, 2016 8:16 pm ] |
| Post subject: | Oil change with Fram PH8A. Oil quantity? |
Changed the oil. Used a Fram PH8A filter. Added 6.3 quarts. Dipstick showed at t he MIN mark. The Fram was larger than what it replaced. I assumed the old filter was OEM. I added the remaining oil up to 7 quarts assuming that the Fram was size equivalent to the Mobile filter. Right or wrong? Is she gonna blow oil? Oh, I read the NOOB guide. Don't know how to paste the pic on the Kindle. |
|
| Author: | olypopper [ Thu Mar 24, 2016 8:57 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Not sure why you'd risk such an expensive engine with such a crappy oil filter? Fram filters were singled out by Cummins several years back and have still continued to have problems with regards to loose internal parts coming apart and killing engines via oil starvation. Drop 7 quarts in and it'll be fine. I'd seriously ditch the fram though. |
|
| Author: | rcdukes [ Thu Mar 24, 2016 9:02 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Simple reason. Didn't know. Hence the reason I read this forum. Haven't seen that about Fram. Sent from my KFAPWI using Tapatalk |
|
| Author: | 95Z28A4 [ Thu Mar 24, 2016 9:44 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
I have cut open several brands of filters. Out of all or them Frams were the poorest quality by a large margin. |
|
| Author: | rcdukes [ Thu Mar 24, 2016 10:12 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Ok. I am a believer now. Gonna change it again. Sent from my KFAPWI using Tapatalk |
|
| Author: | 95Z28A4 [ Thu Mar 24, 2016 10:24 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
I use a WIX 51515XP synthetic media filter. The WIX 51515 is the non-synthetic media version. It is a larger size filter and is a direct replacement for the Fram PH8A. I paid about $7 each including shipping from http://www.Rockauto.com. I bought 14 filters which yielded the lowest cost per filter with shipping. |
|
| Author: | Sir Sam [ Thu Mar 24, 2016 11:31 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Replace with M1-301. http://www.amazon.com/Mobil-M1-301-Exte ... rds=m1-301 |
|
| Author: | mass-hole [ Fri Mar 25, 2016 9:39 am ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
I have heard good things about the Fram Ultra filters but I would use WIX if the Ultras were not available. The people at BITOG seem to think the Ultras are pretty good when I last checked which was a year ago or so. I use the XG8A on my jeep and XG10575 on my F150. |
|
| Author: | flash7210 [ Fri Mar 25, 2016 10:03 am ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
I just did an oil change and used the fram XG8A. I've used the regular PH8A in the past and didn't see a problems with it. Although I am aware the Fram has had some quality control problems. The motorcraft FL-1A is also a good filter. Used it many times. |
|
| Author: | papaindigo [ Fri Mar 25, 2016 11:12 am ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Just a reminder to the OP that the oil dipstick level reading varies from CRD to CRD and is extremely sensitive to "tilt" of the vehicle. To get an accurate level reading be sure you are parked on a flat surface and wait like 5 minutes for the oil to drain to the pan if the engine has been running. The consensus is 6.3-.4 qts for stock size filter (ex. WIX 51516 or NAPA Gold equivalent and 7qts for oversize (ex. WIX 51515 or NAPA Gold equivalent). To check your dipstick for accuracy install filter; add indicated amount of oil; briefly run vehicle; park of flat surface for 5 minutes or so; check level on dipstick mark if need be to show correct full level. FYI the correct low mark would be the same distance below any new full mark as the distance between the OEM markings. |
|
| Author: | olypopper [ Fri Mar 25, 2016 11:49 am ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Long read but it's informative about how Fram "stands behind" their product........or don't. http://www.turbodieselregister.com/thre ... light=fram |
|
| Author: | rcdukes [ Fri Mar 25, 2016 12:11 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
olypopper wrote: Long read but it's informative about how Fram "stands behind" their product........or don't. http://www.turbodieselregister.com/thre ... light=fram Thanks for all the responses. Fram did eventually pony up. I don't think I am up for a fight like that. Not worth my time. I plan on changing the filter. Anyone change JUST the filter? Will it dump all the oil in the pan? |
|
| Author: | WWDiesel [ Fri Mar 25, 2016 3:57 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
rcdukes wrote: Anyone change JUST the filter? Will it dump all the oil in the pan? You can change just the filter without loosing all the oil! Just replace with a new filter and add oil back to the full mark...
|
|
| Author: | MM53 [ Fri Mar 25, 2016 4:23 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Replace with M1-301 or Bosch 3500 |
|
| Author: | WWDiesel [ Fri Mar 25, 2016 5:28 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
The Purolator Pure One PL30001 and the new Purolator Synthetic oil filter PSL30001 made especially for synthetic oils are both very good filters as well... The Purolator Pure One filters are one of the top rated oil filters in the country!!!! Reviews are on the web for those interested! |
|
| Author: | Hexus [ Fri Mar 25, 2016 8:33 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
If you have a NAPA nearby, use a NAPA gold 1515 and use 7 qts. of oil. |
|
| Author: | t0rquey [ Fri Mar 25, 2016 10:57 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
I just bought out my local Meijer's stock of Purolator synthetic 30001's. They were dumping all of them for $4.99 a piece. I just couldn't resist. |
|
| Author: | crasher [ Tue Mar 29, 2016 6:20 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
Sir Sam wrote: Amazon tells me (in bold red letters) that the filter you indicate "does not fit your: 2006 Jeep Liberty", and they already know it's a diesel. ::le-sigh:: |
|
| Author: | flash7210 [ Tue Mar 29, 2016 6:41 pm ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
crasher wrote: Sir Sam wrote: Amazon tells me (in bold red letters) that the filter you indicate "does not fit your: 2006 Jeep Liberty", and they already know it's a diesel. ::le-sigh:: Amazon doesnt know everything. Heck, the local autoparts store will tell you that it doesnt fit. But the M1-301 does fit. |
|
| Author: | funnyman06 [ Wed Mar 30, 2016 5:28 am ] |
| Post subject: | Re: Oil change with Fram PH8A. Oil quantity? |
the M1-301 definitely fits on our little jeeps. |
|
| Page 1 of 2 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|