LOST JEEPS :: View topic - Source for good front axles and intermediate shaft?

My Napa store couldn't find them either. I was on the with the guy and had the part number on a computer screen in front of me. Once i gave him the part numbers he found them.
Left - NMD958354
Right - NMD958355
Sent from my HTC6525LVW using Tapatalk

Well, I put in new front axle/CV's from Rockauto earlier this year. Waste of money and more important my time. I am replacing them with OEMs (one is on back order). These are expensive, but I am sick and tired of replacing cheap Chinese junk. Same goes for the front driveshaft. I just installed a very expensive OEM driveshaft because the properly installed replacement CV joint failed within 5 miles. I put a lot of miles on in a week and cannot afford the down time nor aggravation.

Can anyone confirm length of the CRD shafts? I can measure the Napa shafts tonight as they are at home.

My jeep is not lifted. Is it possible the shafts from Napa would work?

Sent from my HTC6525LVW using Tapatalk

Looks like Napa only liste CV axles for the 3.7 v6 engine. None for either of the 4cyl engines.
Does anybody know exactly what the CV axles lengths should be for the CRD?
Some of the listings on RockAuto state the compressed axle length but I dont know how to be sure they are correct.
When compared to the 3.7 engine axles on RockAuto they do appear to be different but again, I dont know what is correct for either engine.

HER_CRD wrote:

Note of concern: The only engine selection option shown is the 3.7 V6, so any of these may not be correct length for a 2.8 CRD? :roll:

They also list new ones for just a few dollars more!
CV Driveshaft - Left Front - New PART # :NMD 948052
CV Driveshaft - Right Front - New PART # :NMD 948053

https://www.napaonline.com/en/search?te ... ation=true

So no one can confirm the correct NAPA CRD axle half shaft p/be or what the correct lengths are??

MtnClimber wrote:

So no one can confirm the correct NAPA CRD axle half shaft p/be or what the correct lengths are??

This is what I have on file for the CRD Jeep,
I would check with a NAPA store to verify part numbers are correct.
NAPA Axles (reman)
Left - NMD958483 CV Driveshaft Compressed Length 23 3/4 in.
Right - NMD958484 CV Driveshaft Compressed Length 25 1/16 in.

Author:	greiswig [ Mon Oct 16, 2017 7:57 pm ]
Post subject:	Source for good front axles and intermediate shaft?
Looks like mine need replacing at 176k. Anyone know of a good source? I’m told to try to stay away from remanufactured units, but I had pretty good luck with those on a Subaru we had awhile back.

Author:	flash7210 [ Mon Oct 16, 2017 8:18 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
check here: http://www.rockauto.com/en/catalog/jeep,2005,liberty,2.8l+l4+diesel+turbocharged,1431569,drivetrain,axle+shaft,10439 They have both left and right CV axles, intermediate shaft, and the bearing/bushing for the shaft.

Author:	ATXKJ [ Mon Oct 16, 2017 8:22 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
if your local NAPA has re-manufactured units - that's best my Napa didn't - in fact they said their catalog stopped listing the CRD I tried OMIX-ADA but they are physically 1/2" shorter than stock might work on stock - but I'm lifted - drove 1/2 a block and pulled them out sounded like the bearings were being ripped apart. ended up ordering from IDparts - theirs' fit - however returning the cores -best shipping price I could find was $45 for a $50 core not worth the hassle

Author:	HER_CRD [ Mon Oct 16, 2017 8:22 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
I was recommended Napa remain CV shafts. I just ordered the Omixada intermediate shaft from Rock Auto last night. Sent from my HTC6525LVW using Tapatalk

Author:	greiswig [ Tue Oct 17, 2017 8:56 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
Thanks, all. I’d read good things about the NAPA units here, but can’t seem to find a store that can locate them. Maybe it’s because they stopped listing CRDs as ATXKJ mentioned. Maybe if they could look it up by part number? I have a question in to Rock Auto about whether all the axles listed are remans or just the ones that actually say so. A mechanic friend keeps warning me to stay away from remans. Again, thank you.

LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/

Source for good front axles and intermediate shaft? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=87297	Page 1 of 1

Author:	HER_CRD [ Tue Oct 17, 2017 9:09 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
My Napa store couldn't find them either. I was on the with the guy and had the part number on a computer screen in front of me. Once i gave him the part numbers he found them. Left - NMD958354 Right - NMD958355 Sent from my HTC6525LVW using Tapatalk

Author:	WWDiesel [ Tue Oct 17, 2017 9:38 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
HER_CRD wrote: My Napa store couldn't find them either. I was on the with the guy and had the part number on a computer screen in front of me. Once i gave him the part numbers he found them. Left - NMD958354 Right - NMD958355 Sent from my HTC6525LVW using Tapatalk Note of concern: The only engine selection option shown is the 3.7 V6, so any of these may not be correct length for a 2.8 CRD? They also list new ones for just a few dollars more! CV Driveshaft - Left Front - New PART # :NMD 948052 CV Driveshaft - Right Front - New PART # :NMD 948053 https://www.napaonline.com/en/search?te ... ation=true

Author:	mrhemi [ Tue Oct 17, 2017 11:03 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
Well, I put in new front axle/CV's from Rockauto earlier this year. Waste of money and more important my time. I am replacing them with OEMs (one is on back order). These are expensive, but I am sick and tired of replacing cheap Chinese junk. Same goes for the front driveshaft. I just installed a very expensive OEM driveshaft because the properly installed replacement CV joint failed within 5 miles. I put a lot of miles on in a week and cannot afford the down time nor aggravation.

Author:	tjkj2002 [ Tue Oct 17, 2017 11:10 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
If I remember correctly the 2.4 gas KJ uses the same front CV axles as the CRD,those are listed for '02-'05 model years only.

Author:	HER_CRD [ Tue Oct 17, 2017 12:19 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
Can anyone confirm length of the CRD shafts? I can measure the Napa shafts tonight as they are at home. My jeep is not lifted. Is it possible the shafts from Napa would work? Sent from my HTC6525LVW using Tapatalk

Author:	tommudd [ Tue Oct 17, 2017 12:21 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
mrhemi wrote: Well, I put in new front axle/CV's from Rockauto earlier this year. Waste of money and more important my time. I am replacing them with OEMs (one is on back order). These are expensive, but I am sick and tired of replacing cheap Chinese junk. Same goes for the front driveshaft. I just installed a very expensive OEM driveshaft because the properly installed replacement CV joint failed within 5 miles. I put a lot of miles on in a week and cannot afford the down time nor aggravation. My local NAPA has the remmanned ones, customer got a set for his CRD the other day that I installed. Didn't look at numbers but he told me he walked in told them what he had and the had them at the store

Author:	flash7210 [ Tue Oct 17, 2017 12:31 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
Looks like Napa only liste CV axles for the 3.7 v6 engine. None for either of the 4cyl engines. Does anybody know exactly what the CV axles lengths should be for the CRD? Some of the listings on RockAuto state the compressed axle length but I dont know how to be sure they are correct. When compared to the 3.7 engine axles on RockAuto they do appear to be different but again, I dont know what is correct for either engine.

Author:	HER_CRD [ Tue Oct 17, 2017 1:01 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
I'm looking at changing shafts tomorrow. If no one has measurements I can measure mine and report back. Sent from my HTC6525LVW using Tapatalk

Author:	WWDiesel [ Tue Oct 17, 2017 1:29 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
flash7210 wrote: Looks like Napa only liste CV axles for the 3.7 v6 engine. None for either of the 4cyl engines. Does anybody know exactly what the CV axles lengths should be for the CRD? Some of the listings on RockAuto state the compressed axle length but I dont know how to be sure they are correct. When compared to the 3.7 engine axles on RockAuto they do appear to be different but again, I dont know what is correct for either engine. The Mopar part numbers are definitely different between the 2.8 4 cyl. CRD & the 3.7 V6 gasser! Mopar P/N for 3.7 V6 gasser: 52111779AB Axle Shaft Assembly LIBERTY; 3.7L; LEFT 52111778AB Axle Shaft Assembly LIBERTY; 3.7L; RIGHT Mopar P/N for 2.8 4cyl Diesel: 52111781AB Axle Shaft Assembly LIBERTY; 2.8L; LEFT 52111780AB Axle Shaft Assembly LIBERTY; 2.8L; RIGHT NOTE of interest: All 2002-2005 Jeep Liberty with the 4 cyl gas engine use the same CV axle part numbers (L&R) as the 2005-2006 diesel powered Liberty's... So, If they don't list the CRD engine, simply ask for a 02-05 Liberty with the 4 cyl. gas engine! NAPA does not list a 4 cyl. gas engine option either on their web search page! As to axle lengths, found this: Length 52111781AB AXLE HALF 26.63 (in?) Length 52111780AB AXLE HALF 28.06

Page 1 of 1	All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/

Author:	greiswig [ Wed Oct 18, 2017 10:48 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
Thank you all. I’m struck again by how important this community is for sharing hard-won knowledge. I hope I’ve contributed along the way, but I know that I’ve benefited a lot more!

Author:	MtnClimber [ Tue Dec 11, 2018 6:40 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
WWDiesel wrote: HER_CRD wrote: My Napa store couldn't find them either. I was on the with the guy and had the part number on a computer screen in front of me. Once i gave him the part numbers he found them. Left - NMD958354 Right - NMD958355 Sent from my HTC6525LVW using Tapatalk Note of concern: The only engine selection option shown is the 3.7 V6, so any of these may not be correct length for a 2.8 CRD? They also list new ones for just a few dollars more! CV Driveshaft - Left Front - New PART # :NMD 948052 CV Driveshaft - Right Front - New PART # :NMD 948053 https://www.napaonline.com/en/search?te ... ation=true Can anyone confirm the above NAPA P/N's are the correct ones for the CRD as I need to either replace or rebuild my drivers side CV half shaft? I ask as bothe the NMD958354 & the NMD948502 both come up on the NAPA site for the 3.7l gasser not the 2.8l CRD and are also listed as being 24 1/2 in. long instead of 23 3/4 in. in length. Also does anyone know the actual length of the CV axle shafts are for both the CRD and the 3.7l gasser are? Thx - Chris

Author:	MtnClimber [ Thu Dec 13, 2018 10:22 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
So no one can confirm the correct NAPA CRD axle shaft p/n or what the correct lengths are??

Author:	WWDiesel [ Thu Dec 13, 2018 10:40 pm ]
Post subject:	Re: Source for good front axles and intermediate shaft?
MtnClimber wrote: So no one can confirm the correct NAPA CRD axle half shaft p/be or what the correct lengths are?? This is what I have on file for the CRD Jeep, I would check with a NAPA store to verify part numbers are correct. NAPA Axles (reman) Left - NMD958483 CV Driveshaft Compressed Length 23 3/4 in. Right - NMD958484 CV Driveshaft Compressed Length 25 1/16 in.

Author:	MtnClimber [ Sat Dec 15, 2018 12:32 am ]
Post subject:	Re: Source for good front axles and intermediate shaft?
WWDiesel wrote: MtnClimber wrote: So no one can confirm the correct NAPA CRD axle half shaft p/be or what the correct lengths are?? This is what I have on file for the CRD Jeep, I would check with a NAPA store to verify part numbers are correct. NAPA Axles (reman) Left - NMD958483 CV Driveshaft Compressed Length 23 3/4 in. Right - NMD958484 CV Driveshaft Compressed Length 25 1/16 in. WWDiesil - Thanks for the P/N’s as these are different than what I had drummed up. I will call my local NAPA stores to see if available.