LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
Anyone with a Scanguage? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=87543 |
Page 1 of 1 |
Author: | mass-hole [ Thu Dec 14, 2017 11:12 am ] |
Post subject: | Anyone with a Scanguage? |
Does the transmission fluid temp work on the scanguage? If so, can you provide me with the following info for the trans fluid temp guage: TXD RXF RXD MTH If you have a working ambient pressure and temperature sensor as well, the same info would be useful for me. Thanks |
Author: | lfhoward [ Thu Dec 14, 2017 4:07 pm ] |
Post subject: | Re: Anyone with a Scanguage? |
An answer for you might be in here. It’s a long-ish thread that covers many devices, but we have the transmission temp working for the KK on a Scangauge. Maybe the same codes could work with your 06? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=104&t=84482 |
Author: | mass-hole [ Thu Dec 14, 2017 7:54 pm ] |
Post subject: | Re: Anyone with a Scanguage? |
lfhoward wrote: An answer for you might be in here. It’s a long-ish thread that covers many devices, but we have the transmission temp working for the KK on a Scangauge. Maybe the same codes could work with your 06? http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=104&t=84482 Interesting. I had tried the wake up packet previously but I am not sure it was that same PID. I also never tried the Alternate Header option. Thanks. |
Author: | mass-hole [ Fri Dec 15, 2017 10:56 pm ] |
Post subject: | Re: Anyone with a Scanguage? |
I thought I might have had the trans temps working. I found the scanguage inputs for the 2007 Wrangler JK 2.8 CRD which shares a transmission and I believe ECU with us. Unfortunately, I get a reading on Torque, but its definitely not trans temp. |
Author: | ryanchris [ Sat Dec 30, 2017 4:50 pm ] |
Post subject: | Re: Anyone with a Scanguage? |
Mass or anyone how knows, is there a theard with the settings for our jeeps somewhere? I have seen a couple of different posts with different settings and info. Atm I can get torque to work sometimes but only thing that will read more than a few minutes is rpm. (No I don't leave it on all the time just checking stuff , since I know our computers are a kludge and will mess up after so long driving with it on all the time.) I guess I'm just looking for a thread like was posted for the kks.. Maybe I missed it if so my bad Also what the best to use? I've only used torque pro. TIA |
Author: | mass-hole [ Mon Jan 01, 2018 1:31 am ] |
Post subject: | Re: Anyone with a Scanguage? |
ryanchris wrote: Mass or anyone how knows, is there a theard with the settings for our jeeps somewhere? I have seen a couple of different posts with different settings and info. Atm I can get torque to work sometimes but only thing that will read more than a few minutes is rpm. (No I don't leave it on all the time just checking stuff , since I know our computers are a kludge and will mess up after so long driving with it on all the time.) I guess I'm just looking for a thread like was posted for the kks.. Maybe I missed it if so my bad Also what the best to use? I've only used torque pro. TIA Torque pro is what I use. In the vehicle profile settings you need to tell it to use the OBD protocol ISO9141-2 |
Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |