Tonight, I decided to clean out the KJ's MAP sensor. In doing so, the bolt holding the MAP sensor to the manifold went off into never-never land. An hour of searching before it got too dark to continue means that it's gone.

Does anyone have the specs for this bolt? I don't give a darn about keeping the Torx head, but this is the one bolt needed for any sensor attached to the engine that the parts fiche doesn't show.

_________________
2005 KJ CRD Limited 4x4:
245/75R16 BFG TA KO2s
OME / Clevis 2.5" Lift
JBA Lifted A-Arms
IRO WJ Short Rear UCA/WWDiesel mount
Skid Row Skidplates
HDS Model 001 Thermostat (190°F)
Suncoast TC
Full Weeks Kit
Bosch 5V glow plugs
Hayden 2986 fan clutch / GM 11-blade fan
Samco / Sasquatch Intake Hoses
Carter in-tank pump
Provent 200
V6 Airbox

I don't have it but guess would be m8x1.0. I have one I can get to pretty easy on extra intake cover but nothing to size it against unless carry it to Lowes etc. Surely someone will know. It was available via ID parts see link
https://www.idparts.com/sensor-bolt-lib ... -6269.html

_________________
05 Blu LIM, OME GDE Tbo, wk II 245/75/17, KC Lights, bull bar, 195K H TC
05 Blu Lim, Dayton, GDE HT, 255/75/18 , 210K , H TC
06 Bla Lim, GDE Eco, Destination AT 245/75/17, 151K, H TC
06 D Khaki Lim 126K wkII Eur TC
05 D khaki Lim 145k refurbishing
All CRDS: Fumoto, Lift , Fan Shroud mod, fuel head Gen II, SAMCOS,self TB, 2 Mic filt, Hayden

The OEM part no. is: 5010858AA
From memory it is a 4mm or 5mm bolt. I am leaning toward the 5mm.
Just get one of each from your local hardware store and you will be covered.
M 4mm x 0.7 x 12mm length
M 5mm x 0.8 x 12mm length

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

Survey says... M5x0.8, 16mm length. 12mm works just fine, but the manifold is tapped down to at least 16mm.

Thanks, folks! I owe both of you a... Something

_________________
2005 KJ CRD Limited 4x4:
245/75R16 BFG TA KO2s
OME / Clevis 2.5" Lift
JBA Lifted A-Arms
IRO WJ Short Rear UCA/WWDiesel mount
Skid Row Skidplates
HDS Model 001 Thermostat (190°F)
Suncoast TC
Full Weeks Kit
Bosch 5V glow plugs
Hayden 2986 fan clutch / GM 11-blade fan
Samco / Sasquatch Intake Hoses
Carter in-tank pump
Provent 200
V6 Airbox

If you need a similar one, it’s possible to find one on the Internet. Once, I lost a bolt from a MAP sensor, and none of the shops in my area had it.