mste1957 wrote:
I got it out. Pain in the rear.
Congratulations now share the secret of how you did it
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Broke drill bit in bell housing. http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=91734 |
Page 1 of 1 |
| Author: | mste1957 [ Sat Nov 07, 2020 9:13 pm ] |
| Post subject: | Broke drill bit in bell housing. |
Broke the timing pin (1/4 drill bit) in flex plate. Hand cranked and forgot to remove. Any ideas to get out? |
|
| Author: | jws84_02 [ Sun Nov 08, 2020 10:33 am ] |
| Post subject: | Re: Broke drill bit in bell housing. |
Why or how did the pin the break? |
|
| Author: | Jett [ Sun Nov 08, 2020 12:11 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
mste1957 wrote: Broke the timing pin (1/4 drill bit) in flex plate. Hand cranked and forgot to remove. Any ideas to get out? Vacuum cleaner? Strong magnet? Trunk monkey? |
|
| Author: | mste1957 [ Sun Nov 08, 2020 1:30 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
This is how I broke it. After timing belt, I pulled the cam pins and got distracted. When I Came back I started to hand crank and heard a ping and the bit hit the floor. My bad. I have the starter out and the bolt access out. I am going to try to snake a magnet between the ring gear and bell housing. I have hand cranked several times and installed pins each time. Timing is good and it cranks good by hand. Just worried about the 1 inch of drill bit laying on the bottom of bell housing. Any ideas are much appreciated. |
|
| Author: | turblediesel [ Wed Nov 11, 2020 3:53 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
Magnet on a string to drag across the bottom. Or, drool some sort of adhesive to fix it in place, maybe silicon. |
|
| Author: | mste1957 [ Fri Nov 13, 2020 9:49 am ] |
| Post subject: | Re: Broke drill bit in bell housing. |
I got it out. Pain in the rear. |
|
| Author: | snowballs [ Fri Nov 13, 2020 1:57 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
mste1957 wrote: I got it out. Pain in the rear. Congratulations now share the secret of how you did it
|
|
| Author: | mste1957 [ Mon Nov 23, 2020 4:36 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
one inch hole saw and a magnet. Used cell phone camera to see it, but could not get with magnet. Easy once I drilled hole. I put a plug in after I got it out. |
|
| Author: | snowballs [ Tue Nov 24, 2020 8:28 pm ] |
| Post subject: | Re: Broke drill bit in bell housing. |
mste1957 wrote: one inch hole saw and a magnet. Used cell phone camera to see it, but could not get with magnet. Easy once I drilled hole. I put a plug in after I got it out. That's a unique approach; congratulations on the innovation 
|
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|