LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

F driveshaft
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=5&t=92009		 Page 1 of 1
Author:  Chuci [ Sun Jul 18, 2021 9:34 pm ]
Post subject:  F driveshaft
I’m looking to buy a front driveshaft and I was wanting some input on where I could buy a good one. I had already replaced it once and I’ve read on how some of you guys have replaced it numerous times and they keep breaking. Anything is appreciated
Author:  synthetic-oil [ Sat Jul 24, 2021 12:07 pm ]
Post subject:  Re: F driveshaft
https://www.detroitaxle.com/shop/drive- ... md=Liberty
Author:  PZKW108 [ Sat Jul 24, 2021 12:41 pm ]
Post subject:  Re: F driveshaft
synthetic-oil wrote:
https://www.detroitaxle.com/shop/drive-shaft/complete-front-propeller-drive-shaft-assembly-fits-19-weld-to-weld-4x4-only/?vyr=2006&vmk=Jeep&vmd=Liberty


This unit doesn't fit the CRD !
Author:  mtbdemon [ Wed Dec 08, 2021 1:04 pm ]
Post subject:  Re: F driveshaft
I need to do the same thing. Was quoted $800 for the shaft alone and unsure if that’s correct…..I have had no luck in getting the U joints replaced alone
Author:  WWDiesel [ Wed Dec 08, 2021 3:49 pm ]
Post subject:  Re: F driveshaft
mtbdemon wrote:
I need to do the same thing. Was quoted $800 for the shaft alone and unsure if that’s correct…..I have had no luck in getting the U joints replaced alone

I simply replaced the CV joints on the front driveshaft with new ones (kits w/boots) from Detroit Axle. That was about 7 years ago and they are still holding up just fine.
Unless your driveshaft is damaged, it is a whole lot less expensive to simply rebuild/replace current joints. :wink:

https://detroitaxle.com/
#CVK0011(Transfer case end CV joint kit)
#CVK0012(Differential end CV joint kit)
#DR-2 Complete Front Drive Shaft Assembly 19″ Weld to Weld

Another good place to purchase driveshaft parts:
http://www.driveshaftparts.com
ME807B Drive shaft boot kit (Transfer case end boot only, Retainer only)
ME807BK (Transfer case end CV joint kit)
ME709BK (Differential end CV joint kit)
http://www.driveshaftparts.com/index.ph ... arch=me709
DSJ910L -- Jeep Liberty & Cherokee Front Driveshaft 32.5" 52099498AB, 52099498AD, 52111593AA Fits JEEP Grand Cherokee 99-01 8CYL / JEEP Liberty 04-06 2.8L Auto
https://www.driveshaftparts.com/index.p ... uct_id=676
Author:  synthetic-oil [ Sat Dec 18, 2021 11:45 am ]
Post subject:  Re: F driveshaft
PZKW108 wrote:
synthetic-oil wrote:
https://www.detroitaxle.com/shop/drive-shaft/complete-front-propeller-drive-shaft-assembly-fits-19-weld-to-weld-4x4-only/?vyr=2006&vmk=Jeep&vmd=Liberty


This unit doesn't fit the CRD !


But this one does: https://www.driveshaftparts.com/index.p ... h=52111593
Author:  taroo [ Wed Apr 12, 2023 9:53 pm ]
Post subject:  Re: F driveshaft
synthetic-oil wrote:
PZKW108 wrote:
synthetic-oil wrote:
https://www.detroitaxle.com/shop/drive-shaft/complete-front-propeller-drive-shaft-assembly-fits-19-weld-to-weld-4x4-only/?vyr=2006&vmk=Jeep&vmd=Liberty


This unit doesn't fit the CRD !


But this one does: https://www.driveshaftparts.com/index.p ... h=52111593

___

Okay...I am up next. Got the rattle and at least the rear driveshaft CV is going quickly. I want to replace the front and rear driveshaft CV joints at the same time while I am into it.

Are these correct?

Front https://www.driveshaftparts.com/ME709

Rear https://www.driveshaftparts.com/ME807

Or, do I go with this one? https://www.driveshaftparts.com/DSJ910L

Thanks for any thoughts and/or confirmation.

WWDiesel - I saw your thread on CRD Tech and pics. What are your thoughts on if the two items above are the correct front/rear CV kits for the Driveshaft? And if the third link will work for a complete replacement?
Author:  WWDiesel [ Thu Apr 13, 2023 12:34 am ]
Post subject:  Re: F driveshaft
The replacement driveshaft joint kits you listed are the correct numbers.
It is best and less expensive to simply replace your current joints on your driveshaft if it is not damaged. Not a real bad job, just takes a little patience.

As to the complete driveshaft (Mopar calls them propeller shafts), they come in several different lengths, so measuring your current shaft is a MUST to insure you order the correct one.
I have these two Mopar part numbers on file for the 2005 Jeep Liberty KJ CRD: Part Number: 52111596AB or 52853299AB (complete drive shaft)
But measurement is critical!

If you are considering ordering a complete driveshaft, be sure and pay attention to the warning.
Driveshaft Parts wrote:
NOTE: Jeep front driveshafts' come in different lengths. We have noticed that working with the data from Jeep or even the original part number, we have had cases where the data is incorrect.
Due to this we ask our customers to confirm the length of the shaft before purchasing.
You will need the length between the two mounting flanges. This can easily be done even while the shaft is on the vehicle.


Driveshaft Parts lists these different lengths/Part Numbers:
(Fange to Fange Measurement)
    DSJ910 -- Jeep Liberty Cherokee Front Driveshaft 31.3" 52111597AA
    DSJ910L -- Jeep Liberty Cherokee Front Driveshaft 32.5" 52099498AB, 52099498AD, 52111593AA
    DSJ910S -- Jeep Liberty KJ Front Driveshaft 30.3" 52111591AA, 52111591AB
    DSJ910SS -- Jeep Liberty KJ Front Driveshaft 29.3" 52111594AA, 52111596AA, 52111506AB

Image
Author:  taroo [ Thu Apr 13, 2023 9:21 am ]
Post subject:  Re: F driveshaft
Thanks much, Sir. I will drop the old "propeller" shaft and use the kits.

WWDiesel wrote:
The replacement driveshaft joint kits you listed are the correct numbers.
It is best and less expensive to simply replace your current joints on your driveshaft if it is not damaged. Not a real bad job, just takes a little patience.

As to the complete driveshaft (Mopar calls them propeller shafts), they come in several different lengths, so measuring your current shaft is a MUST to insure you order the correct one.
I have these two Mopar part numbers on file for the 2005 Jeep Liberty KJ CRD: Part Number: 52111596AB or 52853299AB (complete drive shaft)
But measurement is critical!

If you are considering ordering a complete driveshaft, be sure and pay attention to the warning.
Driveshaft Parts wrote:
NOTE: Jeep front driveshafts' come in different lengths. We have noticed that working with the data from Jeep or even the original part number, we have had cases where the data is incorrect.
Due to this we ask our customers to confirm the length of the shaft before purchasing.
You will need the length between the two mounting flanges. This can easily be done even while the shaft is on the vehicle.


Driveshaft Parts lists these different lengths/Part Numbers:
(Fange to Fange Measurement)
    DSJ910 -- Jeep Liberty Cherokee Front Driveshaft 31.3" 52111597AA
    DSJ910L -- Jeep Liberty Cherokee Front Driveshaft 32.5" 52099498AB, 52099498AD, 52111593AA
    DSJ910S -- Jeep Liberty KJ Front Driveshaft 30.3" 52111591AA, 52111591AB
    DSJ910SS -- Jeep Liberty KJ Front Driveshaft 29.3" 52111594AA, 52111596AA, 52111506AB

Image
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/