In search of a new replacement turbo for my 05 crd.
My turbo has puked , spitting oil and sparks out of the tailpipe.
Any help is highly appreciated.

_________________
tim l

They can be rebuilt unless you need hard parts.
You can get a used one of eBay and rebuild it. Rockauto has a kit part # 2N-3003SKT and there are YouTube videos on how to do it.
Buy a new Garrett 763360-5001S
Buy a Rotomaster, part #A1200125N
Or get a Mahle 781TC20001000

_________________
2006 KJ CRD AMSOIL Fluids, AMSOIL Oil Filter, AMSOIL ByPass Filter, Secondary Fuel Filter, Provent, Silicone Hoses, Rotomaster Turbo
2013 Audi A3 2.0 TDI Premium Plus
1948 T4 Willis Pickup
1993 C3500 Chevy 6.5 Turbo Diesel
1984 C7500 Chevy Flat Bed 366 gas
1987 R25 Chevy 350 gas

You might try reaching out to Joe Kirian at: Blackbird Innovations, he rebuilds these turbos.
He may be able to salvage yours???
Web page:> https://blackbirdinnovations.com/
Facebook page:> https://www.facebook.com/search/top?q=b ... nnovations
or:> https://www.facebook.com/joe.kirian/

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

If the housings are not damaged to much just rebuild it.

Amazon has center sections.

https://www.amazon.com/dp/B074CLJVKS?psc=1&ref=ppx_yo2ov_dt_b_product_details

for other parts this site has basically everything else. Unison rings, actuators, ect.
https://kbdieselperformance.com/chevy-gmc-duramax/Jeep-CRD-c35277141?offset=9

When disassembling remember there is an alignment pin between the exhaust side and the center section. No twisting or rotating.
Also remember to replace all gaskets and seals on the oil supply and return.

_________________
05 KJ CRD JBA 2.5in lift waiting on an engine rebuild
05 KJ CRD mostly stock currently under the knife
05 KJ CRD mostly stock
18 Ram 3500 crewcab flatbed
kubota M6800

so why not this one from SasquatchParts? https://shop.sasquatchparts.com/products/upgraded-replacement-turbocharger-for-2005-2006-jeep-liberty-28l-crd-5142797ac/

_________________
2005 CRD Limited
SEGR
WEEKS Kit (removed EGR, FCV),
Gen 2 Fuel Head
GDE Eco Tune
ARP studs
Etechno (7v) Glow Plugs
F37
Kap 193 thermostat
Carter Lift Pump (Modified wiring harness)
Fumoto (CRD-108)
Bypass oil filter (2 micron)
Samco
Provent
Sears P-1 Battery
Secondary 2 micron fuel filter

I just put one of those turbos recently and it seems to work fine.

Thanks for your input. As much as I would love to rebuild the one I have,I just don't have enough faith in doing it myself. After all the research I've done I believe the best option is to buy one from Sasquatch Parts. Seems like a little more money than some of the other options, yet cheaper isn't always better.
Again .. Thanks.

_________________
tim l

You might try reaching out to Joe Kirian (diesel_guy86) at: Blackbird Innovations, he rebuilds these Jeep CRD turbos.
Use the PM or email buttons.
You can also contact him over on FB at: https://www.facebook.com/joe.kirian

_________________
Supporting Vendor and Moderator of LOST
05 Jeep Liberty CRD Limited
Ironman Springs/Bilstein/Shocks
Yeti StgIV Hot Tune
Week's BatteryTray
No FCV/EGR
Samcos/ProVent
SunCoast/Transgo
Carter Intank-pmp
2mic.Sec.Fuel Filter
Flowmaster/NO CAT
V6Airbox/noVH
GM11 Bld.fan/HDClutch
IronrockArms/wwdieselMount
98 Dodge Cummins 24 Valve

As turbo replacement goes, this is not a bad deal! And it supports a reputable vendor. What are you waiting for?

_________________
GDE FT Ecotune, EHM, Weeks kit stage 1 & 2, Carter 4600 lift pump, Upgraded tranny, Fishing boat hauler!
New at 164K: head gasket, rockers, exhaust valves, ARP head studs, Injectors, 5v Bosch glow plugs, water pump, timing everything, serpentine everything,
New at 225k: new head, timing belt

UPDATE
I purchased a replacement turbo from Sasquatch Parts.
Everything went smoothly and im back up and running. Since the replacement i have put almost 6000 miles on and no issues. I had it installed at a small shop local and it only took 3 hours. So as of now all is good.
I'd like to thank all you that took time to help with this project.

_________________
tim l

Any idea what in the world caused the carnage in the first place? Must be a learning lesson in there some place.

_________________
GDE FT Ecotune, EHM, Weeks kit stage 1 & 2, Carter 4600 lift pump, Upgraded tranny, Fishing boat hauler!
New at 164K: head gasket, rockers, exhaust valves, ARP head studs, Injectors, 5v Bosch glow plugs, water pump, timing everything, serpentine everything,
New at 225k: new head, timing belt