You could do this CB antenna mount:
http://www.cardomain.com/ride/325889/10
No drilling. Looks stock until one gets a closer look at that THICK antenna. hehehe
| LOST JEEPS http://www.lostjeeps.com/forum/phpBB3/ |
|
| Jack Adaptor and CB Antenna mount http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=59&t=2005 |
Page 1 of 1 |
| Author: | phxtoad [ Sun Sep 18, 2005 6:04 pm ] |
| Post subject: | Jack Adaptor and CB Antenna mount |
For use with farm type lift jacks (Hi-Lift, etc). This device and a simple piece of wood magically allow you to use a jack without marring your KJ sides or pinch welds. See: http://www.cardomain.com/ride/683398/7 Note that my email address is now toad40@cox.net if you want a .pdf of the sketch. Good luck! Edit: This post also includes info on the CB antenna mount I have... |
|
| Author: | CarNutCertifies [ Fri Sep 23, 2005 8:04 pm ] |
| Post subject: | |
hey could you post a pic on how you mounted your CB Antenna? I dont want to drill any holes in my KJ where you can see anyway. Right now i have it mounted on my spare tire carrier and its kinda in the way. |
|
| Author: | phxtoad [ Sun Sep 25, 2005 10:07 pm ] |
| Post subject: | CB antenna |
I'll try to get a pic - but it's really simple: The Fire Stik mounts I have (one for CB, one for a flag) just mount to the body behind the rear light housings. When you pull the light off there is basically a small stretch of flat area where the antenna mount base plate goes. It's thin enough that when you put the light back on, it fits snuggly. TL |
|
| Author: | m0th [ Mon Sep 26, 2005 12:24 am ] |
| Post subject: | |
Are you using the Door Jamb mount for that? |
|
| Author: | phxtoad [ Mon Sep 26, 2005 11:04 pm ] |
| Post subject: | CB |
Yup, I've got the doorjamb mounts... I have my antenna on the outside of the mount (so the antenna is on the outside of the bent mounting plate), but it is possible to mount it on the inside of the mount as well (so the antenna is inside of the bent portion). It's closer to the body and is protected when on the inside. I've never had any issue with it on the outside, however... TL |
|
| Author: | CarNutCertifies [ Tue Sep 27, 2005 12:37 pm ] |
| Post subject: | |
hey thanks for the info i think i will just fab up the mounting tab this weekend. I dont have any stainless but i do have some Aluminum laying around that will be strong enough. maybe i will take some pics and post them for everyone else. |
|
| Author: | AdamIsAdam [ Sat Dec 03, 2005 10:30 pm ] |
| Post subject: | |
You could do this CB antenna mount: http://www.cardomain.com/ride/325889/10
No drilling. Looks stock until one gets a closer look at that THICK antenna. hehehe |
|
| Author: | CarNutCertifies [ Mon Dec 05, 2005 11:33 am ] |
| Post subject: | |
That one looks bulky. you would think it would break. |
|
| Author: | AdamIsAdam [ Mon Dec 05, 2005 11:46 am ] |
| Post subject: | |
It's been there for thousands of miles now, through inclement weather. (Knock wood) The spring relieves most of the pressure. Others have tapped the stock mount instead of drilling it out and using a bolt like I did. This eliminates that bolt head on the bottom, and the double female part under the spring. I've also head a few run it without the spring, which really reduces the bulky look, but I'm afraid that would create too much stress on the mount and/or fender. But overall, it doesn't look bulky in person. It just makes you look twice and say, "hey, is that a CB antenna?" Most people don't notice it at all. |
|
| Page 1 of 1 | All times are UTC - 5 hours [ DST ] |
| Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group http://www.phpbb.com/ |
|