LOST JEEPS
http://www.lostjeeps.com/forum/phpBB3/

Skink Sliders installed!
http://www.lostjeeps.com/forum/phpBB3/viewtopic.php?f=6&t=21047		 Page 1 of 1
Author:  nails023 [ Fri May 25, 2007 8:02 pm ]
Post subject:  Skink Sliders installed!
I finally got my skink sliders installed today. The quality on these is outstanding. I recommend these with no hesitation.

Image

Image

Image
Author:  Tokyojoe [ Fri May 25, 2007 8:12 pm ]
Post subject: 
Saw you yesterday going up Tower Road as I looked out my 3rd floor loft window. If it wasn't you, then there is another silver rugged looking frankie lifted KJ out there that we don't know about. I think it was about 5:30pm.

Looks good. NOW GET OUT THERE AND HIT THE TRAILS WITH US!

HAHAHAHA!!!!!

:lol: :lol:
Author:  tjkj2002 [ Fri May 25, 2007 8:14 pm ]
Post subject: 
Looking good.Now it's time to test them with us on the 9th!
Author:  nails023 [ Fri May 25, 2007 9:39 pm ]
Post subject: 
I will be there this time. I don't have any excuses. I am looking forward to seeing everyone else.
Author:  nails023 [ Fri May 25, 2007 9:50 pm ]
Post subject: 
Tokyojoe wrote:
Saw you yesterday going up Tower Road as I looked out my 3rd floor loft window. If it wasn't you, then there is another silver rugged looking frankie lifted KJ out there that we don't know about. I think it was about 5:30pm.

Looks good. NOW GET OUT THERE AND HIT THE TRAILS WITH US!

HAHAHAHA!!!!!

:lol: :lol:


It wasn't me. I wonder who it was? I havnt seen another one out here yet. :?
Author:  jcphoto20 [ Fri May 25, 2007 10:23 pm ]
Post subject: 
shouldnt they make those so the slider is where that stock bump is? looks like theres two there and makes it unnecessarily low. anyone?
Author:  tjkj2002 [ Fri May 25, 2007 11:19 pm ]
Post subject: 
jcphoto20 wrote:
shouldnt they make those so the slider is where that stock bump is? looks like theres two there and makes it unnecessarily low. anyone?
You do not lose any ground clearance with the Skink sliders,if you get down eye level with them they are flush with the bottom of the unibody "frame" rails.My tranny skid sits lower than my sliders do.
Author:  scottslibby [ Sat May 26, 2007 10:29 pm ]
Post subject: 
I t may have been me I have a silver Libby with a 3inch on it and I live in the area
Author:  jcphoto20 [ Sun May 27, 2007 12:39 am ]
Post subject: 
[quote="tjkj2002"][quote="jcphoto20"]shouldnt they make those so the slider is where that stock bump is? looks like theres two there and makes it unnecessarily low. anyone?[/quote]You do not lose any ground clearance with the Skink sliders,if you get down eye level with them they are flush with the bottom of the unibody "frame" rails.My tranny skid sits lower than my sliders do.[/quote]

i didnt think it lost ground clearance on level ground, i meant on the side, where it is, looks silly to me, should be up where the other bump is, you would have more clearance from rocks on the side before you had to slide on them if they put them where they should have, they could be another couple inches higher
Author:  Donnie [ Sun May 27, 2007 8:43 pm ]
Post subject: 
jcphoto20 wrote:
tjkj2002 wrote:
jcphoto20 wrote:
shouldnt they make those so the slider is where that stock bump is? looks like theres two there and makes it unnecessarily low. anyone?
You do not lose any ground clearance with the Skink sliders,if you get down eye level with them they are flush with the bottom of the unibody "frame" rails.My tranny skid sits lower than my sliders do.


i didnt think it lost ground clearance on level ground, i meant on the side, where it is, looks silly to me, should be up where the other bump is, you would have more clearance from rocks on the side before you had to slide on them if they put them where they should have, they could be another couple inches higher


The would equate to a moveable metal piece against the paint, do you think that would be a good idea? Talk about scratches and possibly messing up your rocker and door panels. Stop being such a negative nelly :).
Author:  tjkj2002 [ Sun May 27, 2007 8:48 pm ]
Post subject: 
jcphoto20 wrote:
tjkj2002 wrote:
jcphoto20 wrote:
shouldnt they make those so the slider is where that stock bump is? looks like theres two there and makes it unnecessarily low. anyone?
You do not lose any ground clearance with the Skink sliders,if you get down eye level with them they are flush with the bottom of the unibody "frame" rails.My tranny skid sits lower than my sliders do.


i didnt think it lost ground clearance on level ground, i meant on the side, where it is, looks silly to me, should be up where the other bump is, you would have more clearance from rocks on the side before you had to slide on them if they put them where they should have, they could be another couple inches higher
When they did the redesign of the KJ for '05-'07's that piece of black plastic just covers the metal rocker panel that is not covered in the older years.If you cut that off you'd be cutting the rocker panels and pinch seems off(where the Skinks attach to).Trust me you don't loose any clearence with the Skink sliders,they are worth there wieght in gold if you play on the rocks.
Author:  Skyjump136 [ Mon May 28, 2007 11:07 am ]
Post subject: 
Quote:
i didnt think it lost ground clearance on level ground, i meant on the side, where it is, looks silly to me, should be up where the other bump is, you would have more clearance from rocks on the side before you had to slide on them if they put them where they should have, they could be another couple inches higher


I don't think you understand what's under the "bump"...actually just a plastic cover that goes over the rocker panel. If Rock Lizard or Boulder Bars were to sit up there then you'd have to cut off the very part of your vehicle that you are trying to protect.
Author:  Big D [ Mon May 28, 2007 11:17 am ]
Post subject: 
You also want the rock rails to be parallel with the driveline. That way if you go over a rock it will come down on the rock rail. Although, if you do slip it might hit the door.
Author:  andrew c [ Sat Jun 16, 2007 11:32 pm ]
Post subject: 
Looks good man! maybe I should get one.
Author:  Rock Lizard [ Sat Jun 16, 2007 11:35 pm ]
Post subject: 
andrew c wrote:
Looks good man! maybe I should get one.


They work better if you get both sides. :twisted:
Author:  andrew c [ Sat Jun 16, 2007 11:35 pm ]
Post subject: 
Can someone pm me the website where I can get one?
Author:  Tokyojoe [ Sat Jun 16, 2007 11:35 pm ]
Post subject: 
What side are you going to put that ONE slider on?
Author:  andrew c [ Sat Jun 16, 2007 11:39 pm ]
Post subject: 
Or two,.....^^^ thats kinda what i ment buddy,...
Author:  Tokyojoe [ Sat Jun 16, 2007 11:41 pm ]
Post subject: 
What you meant and what you said are two different things.

What you say/type gives room for joking around, buddy.
Author:  meh_kick [ Mon Jun 18, 2007 2:43 pm ]
Post subject: 
http://www.rocklizardfabrications.com/
Page 1 of 1 All times are UTC - 5 hours [ DST ]
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/